Why choose Aruba 303h hospitality access point?
DATA SHEET ARUBA 303H HOSPITALITY ACCESS POINT High-performance 802.11ac Wave 2 (Wi-Fi 5) access point for hospitality and branch offices The multi-functional Wave 2 303H access point delivers best-in class Wi-Fi connectivity for hospitality and branch offices, enabling an always-on user experience with low Total Cost of Ownership (TCO).
How many antennas does the Aruba 303h have?
DATA SHEET ARUBA 303H HOSPITALITY ACCESS POINT 4 WI-FI ANTENNAS • Two integrated dual-band moderately directional antennas for 2x2 MIMO with maximum individual antenna gain of 4.3dBi in 2.4GHz and 6.2dBi in 5GHz.
How many active Ethernet ports does the 303h series access point have?
The 303H Series access point is equipped with four active Ethernet ports (E0/PT-E3), shown in Figure 2 (E0) and Figure 4 (E1-E3).
How to install 303h series hospitality access points?
11Aruba 303H Series Hospitality Access Points| Installation Guide Connect the equipment into an outlet on a circuit that is different from that to which the receiver is connected. Consult the dealer or an experienced radio or television technician for help.
What is Aruba remote Access Point?
Aruba Remote Access Points (RAPs) provide secure always-on network access to corporate enterprise resources from remote locations.
How do I setup my Aruba wireless access point?
0:362:26Aruba: How to set up your remote access point - YouTubeYouTubeStart of suggested clipEnd of suggested clipFirst find your plastic desktop mount and snap it onto your wrap. So it can stand on its own like.MoreFirst find your plastic desktop mount and snap it onto your wrap. So it can stand on its own like. This next find an Ethernet port on your wrap labeled e0.
Is Aruba access point good?
Access point Aruba is very reliable, efficient and stable. In the organization, we use the IAP version, which does not require a physical controller. All access points are managed from the central AirWave server, which also monitors devices and wifi networks.
How do I setup a remote access point?
Navigate to Configuration > AP Installation (under Wireless.) Select the required remote AP under the Provisioning tab and then click Provision. Select Yes for Remote AP and Certificate for Remote AP Authentication Method. Click Apply and Reboot to apply the configuration and reboot the AP as certificate RAP.
How does a wireless access point work?
Access points work by connecting direct to your broadband router or network switch with a Ethernet or data cable. This provides the AP with the internet connection and bandwidth required. It then transmits and receives a wireless signal in either the 2.4Ghz or 5Ghz frequency range (WIFI).
What is the default IP address of Aruba access point?
The default IP address of the controller is 172.16. 0.254. Connect a PC or workstation to any line port on the controller, then enter this IP address into a supported Web browser to launch the Setup Wizard. To run the Setup Wizard: 1.
Do Aruba access points need a controller?
Aruba Instant is a wireless access point operating system and platform that does not require the purchase of hardware/virtual controllers for deployment.
Is Aruba a router?
Aruba Instant On access points replace a typical router. Just plug an Aruba Instant On access point into the cable that brings the internet into your home to enable your Wi-Fi network.
Who makes Aruba APS?
Hewlett Packard EnterpriseAruba NetworksTypeSubsidiaryRevenueUS$3 billion (FY 2019)Number of employees6000+ParentHewlett Packard EnterpriseWebsitewww.arubanetworks.com4 more rows
How do I assign an IP address to an access point?
Log in to the access point's web-based setup page. Launch a web browser and enter the access point's IP address in the Address bar then press Enter. Step 2: Once the setup page appears, click the Network Setup drop-down and select Static IP.
Does access point need to be wired?
A Wireless Access Point (WAP) allows several devices to connect via WiFi to a single network. The wired equivalent is a switch. But unlike a switch, a WAP does not need to be wired to the router. Access Points connect via wired Ethernet to a switch, or a switch port on a router, then serve up WiFi.
Does access point have IP address?
Wifi access points need not have an IP address, any more than wired switches and hubs do. However a large number do, as they also act on the IP layer as DHCP servers and network gateways.
How do I reset my Aruba access point?
To reset a n Instant AP, perform the following steps:Turn off the Instant AP.Press and hold the reset knob using a small and narrow object such as a paperclip.Turn on the Instant AP without releasing the reset knob. The power LED. ... Release the reset knob. The Instant AP reboots with the factory default settings.
How do I change my Aruba access point Wi-Fi password?
You can update your password details by using the WebUI or the CLI....To change the admin user password:Navigate to Configuration > System > Admin.Under Local, provide a new password that you would like the admin users to use.Click Save.
Is Aruba Instant on a router?
An Aruba Instant On AP acts as a network router as well. In short, this means plugging in directly to the Internet right out of the box allows network setup to begin immediately. Aruba Instant On devices require no licenses, subscriptions, renewals, or prepaid contracts.
What is Aruba activate?
For large installations across multiple sites, the Aruba Activate service significantly reduces deployment time by automating device provisioning, firmware upgrades, and inventory management. With Aruba Activate, APs in Instant mode can configure themselves when powered up.
What is the maximum data rate for 303H AP?
With a maximum concurrent data rate of 867Mbps in the 5GHz band and 300Mbps in the 2.4GHz band, the 303H AP delivers high-performance Gigabit Wi-Fi for hospitality and branch environments at an attractive price point. It supports multi-user MIMO (MU-MIMO) and 2 spatial streams (2SS) to provide simultaneous data transmission for up to 2 devices, maximizing data throughput and improving network efficiency.
What is 303H AP?
The 303H AP is a unified AP that supports both controller-based and controllerless deployment modes, providing maximum flexibility
What is integrated wireless intrusion protection?
Integrated wireless intrusion protection ofers threat protection and mitigation, and eliminates the need for separate RF sensors and security appliances.
What is a Wave 2 303H?
The 802.11ac Wave 2 303H AP combines wireless and wired access in a single compact device. Three local Gigabit Ethernet ports are available to securely attach wired devices to your network. One of these ports is also capable of supplying PoE power to the attached device.
Can a 303H be used as a remote AP?
The 303H ships with everything you need to deploy as a wall-mounted (hospitality) AP, attaching directly to a standard single-gang data wall-box. The 303H can also be easily converted to a desk mounted (remote) AP, using an optional accessory stand.
Can 303H be mounted to a wall box?
The 303H AP can be easily mounted to a standard data wall-box using the existing structured cabling system or converted to a desk mounted AP using an optional mounting kit. It is ideal for schools (dormitories, classrooms), hotels, medical clinics, branch offices and remote workstations which often require flexible and easy deployment options.
What is Aruba 303H?
The Aruba 303H Series access point is a high-performance dual-radio wireless device for hospitality and branch
How many DC can a 303H access point handle?
The 303H Series access point supports up to 48V DC when using an AP-AC-48V36C power adapter (sold
How much power does the E3 port have?
Additionally, the E3 port supports PoE- out functionality, and is capable of supplying up to 15.4W to PSE when the
Where is the E0/PT port located?
The E0/PT port, located at the back of the access point is 10/100/1000Base-T, auto-sensing, MDI/MDX
Where is the Micro B connector located?
The 5-pin Micro-B connector located on the back of this device . Use an AP-CBL-SERU cable for direct
Where is the Ethernet port located on a laptop?
Alternatively, the wired Ethernet ports located on the bottom of the device allow users to connect to the device
Where is the network status LED located?
The Network Status LED, located on the sides of the E1-E 3 ports, indicates activity transmitted to/from the wired
