What is the Aruba rap-3?
The multifunctional Aruba RAP-3 delivers secure 802.11n wireless and wired network access to corporate resources from branch and home offices. Centrally managed by Aruba Mobility Controllers, the RAP-3 extends corporate resources to remote locations by establishing site-to-site VPN tunnels to the data center.
What is Aruba secure remote access point service?
The Secure Remote Access Point Service allows AP users, at remote locations, to connect to a n Aruba Managed Device over the Internet. As the Internet is involved, data traffic between the Managed Device and the remote AP Remote APs extend corporate network to the users working from home or at temporary work sites.
How many Ethernet ports does the rap-3 have?
Delivering a wireless data rate of up to 300 Mbps, the RAP-3 has three 10/100BASE-T Ethernet ports and one USB port for connecting to 3G and 4G networks. It is also available with an 802.3af power-over-Ethernet (PoE) port (RAP-3WNP model) for IP phones or other devices.
What are the features of the rap-3 network?
The RAP-3 also offers a variety of enterprise-class features, including role-based network access, policy-based forwarding, and Adaptive Radio Management (ARM), which gives remote workers the same high-quality Wi-Fi experience they get at corporate headquarters.
What is Aruba remote Access Point?
Aruba Remote Access Points (RAPs) provide secure always-on network access to corporate enterprise resources from remote locations.
What is a rap Access Point?
The multifunctional Aruba RAP-3 delivers secure 802.11n wireless and wired network access to corporate resources from branch and home offices. Centrally managed by Aruba Mobility Controllers, the RAP-3 extends corporate resources to remote locations by establishing site-to-site VPN tunnels to the data center.
Is Aruba RAP in a router?
Aruba Networks RAP-5WN Wireless Router - IEEE 802.11n.
How do I setup my Aruba wireless Access Point?
0:362:26Aruba: How to set up your remote access point - YouTubeYouTubeStart of suggested clipEnd of suggested clipFirst find your plastic desktop mount and snap it onto your wrap. So it can stand on its own like.MoreFirst find your plastic desktop mount and snap it onto your wrap. So it can stand on its own like. This next find an Ethernet port on your wrap labeled e0.
How do you set up rap?
Navigate to Configuration > AP Installation (under Wireless.) Select the required remote AP under the Provisioning tab and then click Provision. Select Yes for Remote AP and Certificate for Remote AP Authentication Method. Click Apply and Reboot to apply the configuration and reboot the AP as certificate RAP.
What is the differences between remote access and site to site VPN?
A remote access VPN connects remote users from any location to a corporate network. A site-to-site VPN, meanwhile, connects individual networks to each other.
How do Aruba raps work?
Any Aruba access point can be provisioned to operate as a RAP. The purpose of deploying a RAP is to leverage the wireless and wired features of an Aruba access point from a remote location across the Internet. The RAP is configured to use IPsec to connect to a Mobility Controller's public IP over UDP 4500 for NAT-T.
What is Aruba Activate?
Activate is a kick-start for your Aruba Instant deployment. Activate enables a network installer to simply plug a new Instant Access Point into an internet connection anywhere in the world, plug in power (or PoE), wait for the AP's radio LEDs to light up and move on to the next location!
How does a wireless access point work?
Access points work by connecting direct to your broadband router or network switch with a Ethernet or data cable. This provides the AP with the internet connection and bandwidth required. It then transmits and receives a wireless signal in either the 2.4Ghz or 5Ghz frequency range (WIFI).
What is the default IP address of Aruba access point?
The default IP address of the controller is 172.16. 0.254. Connect a PC or workstation to any line port on the controller, then enter this IP address into a supported Web browser to launch the Setup Wizard. To run the Setup Wizard: 1.
Does Aruba Instant On require a router?
The Instant On AP must be directly connected to the internet modem with no other device in between. It must therefore be the only AP connected to the internet. Other APs have to be powered down initially and added later through mesh using the extend network capability.
How do I reset my Aruba access point?
To reset a n Instant AP, perform the following steps:Turn off the Instant AP.Press and hold the reset knob using a small and narrow object such as a paperclip.Turn on the Instant AP without releasing the reset knob. The power LED. ... Release the reset knob. The Instant AP reboots with the factory default settings.
How do I change my Aruba access point Wi-Fi password?
You can update your password details by using the WebUI or the CLI....To change the admin user password:Navigate to Configuration > System > Admin.Under Local, provide a new password that you would like the admin users to use.Click Save.
What is Aruba Rap 3?
The multifunctional Aruba RAP-3 delivers secure 802.11n wireless and wired network access to corporate resources from branch and home offices.
What is Aruba activate?
For large installations across multiple sites, the Aruba Activate service significantly reduces deployment time by automating device provisioning, firmware upgrades, and inventory management. With Aruba Activate, Instant APs are factory-shipped to any site and configure themselves when powered up.
How many Ethernet ports does the Rap 3 have?
Delivering a wireless data rate of up to 300 Mbps, the RAP-3 has three 10/100BASE-T Ethernet ports and one USB port for connecting to 3G and 4G networks. It is also available with an 802.3af power-over-Ethernet (PoE) port (RAP-3WNP model) for IP phones or other devices.
Can a RAP 3 join an Aruba cluster?
At locations that require greater coverage, the RAP-3 can join an Aruba Instant WLAN cluster. Simply install additional RAP-3s or any Instant AP and the entire cluster is managed as one. If one Instant AP fails, another AP automatically takes over with no disruption.
What is zero touch?
Zero Touch: RAPs have a GUI where the user can enter the IP address or URL of the controller. Activate: RAPs can also automatically communicate with Aruba cloud based Activate. If an entry exists in Activate it will direct these RAPS to the controller.
Do you need a PEFV for raps?
RAPs do not require PEFV. Only the regular AP licenses (AP, PEFNG).
