How to configure Aruba access points as a secure remote access point service?
Make sure that the L2TP IP pool configured on the local controller (from which the remote AP obtains its address) is reachable in the network by the master controller. The tasks for configuring an Aruba Access Points as a Secure Remote Access Point Service are: Configure a public IP address for the controller.
How to enable default password recovery in ArubaOS?
To enable the default password recovery user, execute the following command in the configuration mode: Starting with ArubaOS 8.4.0.0, an alternate password recovery user with a username and password can be created to reset the admin password. The alternate user’s username can be 16 characters long and the password can be 32 characters long.
When should I deploy an IPSec VPN tunnel in Aruba?
(Aruba recommends this deployment when AP-to-controllercommunications on a private network need to be secured.) In this scenario, the remote AP uses the controller’s IP address on the private network to establish the IPSec VPN tunnel.
How do I recover a password from a remote device?
Password recovery access using either the default password recovery user or the alternate password recovery user is allowed only through the serial console of a controller. Secure Shell. SSH is a network protocol that provides secure access to a remote device.
How do I reset my Aruba access point password?
Resetting Admin PasswordConnect a local console to the serial port on the managed device.From the console, login into the managed device as a password recovery user. ... Enter configuration mode by typing in configure terminal.To reset the administrator user account password, use the mgmt-user admin root command.More items...
How do I reset the admin password on Aruba Instant?
To reset the admin password on Aruba Instant: From the console, enter this username and password: Username: admin. Password: forgetme! Get into configure terminal mode: # configure terminal. Issue this command to reset the password:
What is the default IP address of Aruba access point?
The default IP address of the controller is 172.16. 0.254. Connect a PC or workstation to any line port on the controller, then enter this IP address into a supported Web browser to launch the Setup Wizard. To run the Setup Wizard: 1.
How do I log into Aruba IAP?
Password—Enter the Serial Number of the Instant AP. When you use a provisioning Wi-Fi. Wi-Fi can apply to products that use any 802.11 standard. network to connect to the Internet, all browser requests are directed to the Instant UI .
How do I change my access point password?
0:131:31How to change router password - YouTubeYouTubeStart of suggested clipEnd of suggested clipYou just click on login it should bring you right into the configuration page of the router. From.MoreYou just click on login it should bring you right into the configuration page of the router. From. There you just want to click on the tools tab at the top.
What is the default password that is required for the admin account while under the Service OS console?
After connecting to the switch console port, a reboot is performed and the Service OS console is accessed as shown above. What is the default password that is required for the admin account while under the Service OS console? C. "forgetme!"
How do I connect to Aruba AP?
Connect the power cable to the power supply.Connect the power cable to the Aruba AP and plug the power into power.Connect the provided network cable to the black E0/PT connection on the bottom of the Aruba AP. ... Connect the other end of the network cable into an open port on your wireless router.More items...•
How do I configure my Aruba access point?
Aruba Central - How to Configure AP SettingsClick Configuration, Wireless.Select a group and then click Access Points. ... Click the AP that user want to customize.Click Edit. ... Configure the parameters described in table below as required and then click Save Settings. ... Click Save Settings and reboot the AP.
How do I connect to Aruba Instant AP?
Setting Up Your Wired NetworkEnsure that the Instant On switch is connected to the internet to be discovered.Connect the port you want to use as your switch uplink to your local network using an Ethernet cable, then power it on. ... Power on the switch. ... Download the mobile app on your Android or iOS device.
How do I reset my Aruba Instant AP?
To reset a n Instant AP, perform the following steps:Turn off the Instant AP.Press and hold the reset knob using a small and narrow object such as a paperclip.Turn on the Instant AP without releasing the reset knob. The power LED. ... Release the reset knob. The Instant AP reboots with the factory default settings.
How do I reset my Aruba switch?
Switch to the configuration context with the command config. Erase all user information and configuration, restoring the switch to its factory default state with the command erase all zeroize. Enter Y when prompted to continue. The switch automatically restarts.
How do I reset my Aruba 2930f switch?
Restore the factory default configurationPress Clear and Reset simultaneously.While continuing to press Clear, release Reset.When the Global Status LED begins to fast flash orange (after approximately 5 seconds), release Clear.
How do I reset my Aruba 2540?
To do this:Press and hold the Reset button.While holding the Reset button, press and hold the Clear button.Release the Reset button.When the Test LED to the right of the Clear button begins flashing, release the Clear button. It takes approximately 20-25 seconds for the switch to reboot.
What is SSH in Aruba?
SSH is a network protocol that provides secure access to a remote device. sessions and serial console sessions with a controller and not through WebUI. Aruba recommends to enable the default password recovery user before generating and sharing the tech-support logs or configuration files with customer support.
How to recover password on managed device?
Use this procedure if the administrator user account password is lost or forgotten. 1. Connect a local console to the serial port on the managed device. 2. From the console, login into the managed device as a password recovery user. For information, read Password Recovery user.
What is password recovery?
A password recovery user is a management user with root rights that is used to reset the admin password in the event of a lost or forgotten password. Starting with ArubaOS 8.4.0.0, a configurable alternate password recovery user can be created in addition to the default password recovery feature.
Can you see alternate password recovery in WebUI?
The alternate password recovery user will not be shown in the management user section of the WebUI. This user role cannot be configured through the WebUI.
Can you recover passwords through serial console?
Password recovery access using either the default password recovery user or the alternate password recovery user is allowed only through the serial console of a controller.
What is remote AP?
The remote AP requires an IP address to which it can connect to establish a VPN tunnel to the controller. This can be either a routable IP address you configure on the controller, or the address of an external router or firewall that forwards traffic to the controller.
How to configure L2TP IP pool?
To configure the L2TP IP pool, click Add in the Address Pools section. Configure the L2TP pool from which the APs will be assigned addresses, then click Done.
How to provision an AP?
The easiest way to provision an AP is to use the Provisioning page in the WebUI, as described in the following steps: 1. Navigate to the Configuration > Wireless > AP Installation > Provisioning page. Select the remote AP and click Provision. 2.
How to find IP address parameter in local database?
To view IP address parameter in the local database, navigate to the Configuration > Security > Authentication > Servers > Internal DB page .
What port does a secure controller use?
Communication between the AP and the secure controller uses the UDP 4500 port. When both the controller and the AP are behind NAT devices, configure the AP to use the NAT device’s public address as its master address. On the NAT device, you must enable NAT-T (UDP port 4500 only) and forward all packets to the public address of the NAT device on UDP port 4500 to the controller to ensure that the remote AP boots successfully.
What port is NAT T?
On the NAT device, you must enable NAT-T (UDP port 4500 only) and forward all packets to the public address of the NAT device on UDP port 4500 to the controller to ensure that the remote AP boots successfully.
Can a rap be authenticated?
RAPs can now establish a PPPoE session with a PPPoE server at the ISP side and get authenticated using the Challenge Handshake Authentication Protocol (CHAP). The PPPoE client running on a RAP is capable of handling the CHAP authentication requests from the PPPoE server.
