Remote-access Guide

axis camera enable remote access

by Prof. Tara Keeling PhD Published 2 years ago Updated 2 years ago
image

1. From the same network as the server, log on to the AXIS Camera Station server with an administrator user. 2. Go to Configuration > Connected services > Axis Secure Remote Access.May 17, 2018

How do I access my axis camera from the Internet?

To access your site from a remote location open up AXIS Camera Companion 2.0 and log in with the same MyAxis account as used on the local site. Select the remote site, type in the site password and press Enter. You should now be connected to the site. your cameras and router up manually.

How do I access axis NVR?

0:201:26AXIS Camera Station Secure remote access - YouTubeYouTubeStart of suggested clipEnd of suggested clipAnd selects access secure remote access insert your my access account and your password. Click applyMoreAnd selects access secure remote access insert your my access account and your password. Click apply you can then enable secure remote access once secure remote access has been enabled on the server.

What is the default IP for AXIS camera?

192.168.0.90The default IP address for the Axis cameras and video encoders is 192.168. 0.90. More information can be looked up here.

How do I find the IP address of my axis camera?

Discovering Your Axis Camera With Your Room Alert Account To navigate to the camera's Device Details page, select Devices in the navigation bar to the left in your Room Alert Account, and then select your camera from the device list. You may find the unit's IP address listed under Local IP.

What is AXIS camera default password?

root/passAxis: Traditionally root/pass, new Axis cameras require password creation during first login (note that root/pass may be used for ONVIF access, but logging into the camera requires root password creation) Basler: admin/admin.

Is Axis Camera Station free?

Axis Camera Station One is a FREE software solution for the simultaneous viewing and recording of high-quality H. 264, MPEG-4 and Motion JPEG video from a single surveillance camera.

How do I reset my axis camera remotely?

Remote reboot Axis IP cameraIn Windows open the Command Prompt.At the command prompt type in (without quotes) “FTP ”You should be now asked to enter a username. ... Once you are logged into the camera type in this command press enter and re-type the command again and press enter again.

How do I reset my axis camera to default IP?

0:361:43Solved in 60 seconds: How to factory reset an Axis network cameraYouTubeStart of suggested clipEnd of suggested clipKeep the control button pressed for 15 to 30 seconds until the status LED indicator flashes greenMoreKeep the control button pressed for 15 to 30 seconds until the status LED indicator flashes green and yellow. Then release the control button and eventually you should see the LED turn green.

How do I reset my axis camera?

Axis Factory ResetDisconnect the camera from the power supply and ethernet.Remove the four screws securing the rear cover and remove it.Keep the Control button pressed while you restore the power supply.Hold down the button for about 15 seconds until the status LED is yellow flashing.Release the Control Button.

What is Axis IP utility?

AXIS IP Utility helps you set the IP address of an Axis network video product. Axis devices on the network are automatically discovered and displayed. Assign network parameters (IP Address, Subnet mask and Default router) or configure the device to obtain its IP address from DHCP .

How do I assign an IP address to my IP camera?

Configuring the IP address of the cameraOpen a web browser like Internet Explorer then enter the camera's IP address in the Address bar.Enter your camera's User name and Password then click OK.Click the Setup tab.Click Basic located at the left side of the page.Select the Configuration Type.

What is IP utility?

IP Utility is a free, Windows-based application tool with friendly user interface. It helps you locate available devices including cameras, video encoders, and standalone NVRs in the network by showing its IP address.

How do I use NVR?

Here is how to proceed:Take an Ethernet cable to connect the LAN port on the external PoE switch and the router. Then connect the router with the non-PoE NVR.Use Ethernet cables to connect all IP cameras to the PoE switch RJ45 ports. ... Use an HDMI cable or VGA cable to connect the monitor and the NVR.

How do I enable ONVIF axis?

If you are unable to find ONVIF user settings, please check this setting to ensure that ONVIF/Web Service is enabled.Navigate to System Options > Support > System Overview.Click ONVIF/Web service.Enable ONVIF/Web service by checking the box next to Enable Web Service.Press the Save button.

Why NVR Cannot detect IP camera?

If you aren't getting a video feed from an ip camera, the first step you need to take is to bench test your camera. Take the camera down and connect directly to the NVR or PoE switch with a short pre-made Cat5 cable. 90% of the time a camera that disconnects/does not power, indicates a problem with the cable.

How do I connect NVR to PoE switch?

How to connect a POE Switch to a NVR designed for POE Switches:Plug the IP Cameras into the POE Switch.Plug the POE switch into the NIC 2 on the NVR.Plug the POE switch into the wall outlet.Follow the instructions on how to tell the NVR to add and record those cameras:

What happens when a camera makes an outbound connection through the router?

Each time a client or a camera makes an outbound connection through the router, the router will give that connection a random external port which is used for hole punching. It is not possible to predict which port will be used.

Does Axis require authentication?

AXIS Secure Remote Access does not support proxy that requires authentication. A possible workaround could be to allow cameras (AXIS Companion) and AXIS Camera Station server (AXIS Camera Station) to bypass authentication. Each time a client or a camera makes an outbound connection through the router, the router will give ...

How to add camera station to Axis server?

2. Go to Configuration> Security> User permissions. 3. In the bottom right of the window, click Add.

How to view Axis camera station?

1. Open the AXIS Camera Station Windows app. 2. Select Remote server. 3. Select a server in the list or type the IP address of the AXIS Camera Station server. If Simple Service Discovery Protocol (SSDP) is allowed on the local network you can expand the dropdown list to view all local servers.

What is the default port for Axis Camera Station?

If you run more than one server on the same network requiring port mapping, you must change the AXIS Camera Station default port (55752) . Each server must have a unique port.

Does Axis Camera Station use firewall?

During the installation, AXIS Camera Station automatically configures the Windows firewall exceptions for incoming traffic used by AXIS Camera Station. If you use a third-party firewall, you might have to request for a similar set of exceptions to be added to the configuration. In most cases only the “Inbound” port range of 55752 to 55757 requires an exception.

Does Axis take responsibility for a configuration?

Please note that AXIS doesn’t take any responsibility for how this configuration may affect your system. If the modification fails or if you get other unexpected results, you may have to restore the settings to default.

Can Axis camera station be used on domain?

AXIS Camera Station allows you to use both local Windows and domain users and user groups. If you use a domain setup, you must join the server to the domain. Your IT department might have to help you with this

How to connect to Axis server?

To connect to a server, go to Main menu > Servers > New connection: If the server is on the network, select Remote server and select a server from the drop-down list or enter the IP address or DNS address in the Remote server field.

How to manage devices in Axis?

In AXIS Device Manager, go to Device manager > Manage devices.

How to log in as current user?

To log in as the current Windows user, click Log in . If you clear Log on as current user you need to enter a username and password in the next step. Add devices: AXIS Device Manager automatically searches for Axis devices on the network and adds them to the list of devices.

What is the Axis password?

The device password is the primary protection for your data and services. Axis devices do not impose a password policy as they may be used in various types of installations. To protect your data we strongly recommend that you: Use a password with at least 8 characters, preferably created by a password generator.

What is an axis device?

Axis devices are designed to be used on an Ethernet network. To access the device’s webpage you need an IP address. Most networks have a DHCP server that automatically assigns IP addresses to connected devices.

What is Axis Device Manager?

AXIS Device Manager automatically searches for Axis devices on the network and adds them to the list of devices.

How to add device from IP address?

To add a device from a specific IP address, go to Device manager > Manage devices and click Add device from address. To access the device from an external browser, click the address link in the list.

How to activate Axis Secure Remote Access?

In the Axis mobile viewing app, remote access needs to be activated first by signing in with the same MyAxis account as the one used to enable Axis Secure Remote Access on the remote server. When signed in, the total amount of relayed data used by the MyAxis account during the month will be shown.

What is live view in Axis?

The live view shows the views and cameras and live videos from the connected cameras. When connecting to multiple AXIS Camera Station servers, all the views and cameras of connected servers are displayed grouped by the server name.

What is the port 55752?

The ports 55752 (HTTP), 55754 (TCP), 55756 (mobile communication), and 55757 (mobile streaming) are used on AXIS Camera Station Server for communication between the server and the client. If required, the ports can be changed from AXIS Camera Station Service Control. See General in AXIS Camera Station Service Control.

How long does it take to renew a certificate in Axis?

Renew certificate between the server and devices: If you have configured AXIS Camera Station as a certificate authority, the client or server certificates generated by AXIS Camera Station will automatically be renewed 7 days before the expiration warning is configured to appear if you have selected Remember passphrase. If you want to renew or update a certificate manually, follow the same steps as enabling HTTPS or IEEE 802.1X.

Why is frame rate limited in live view?

The resolution and frame rate used in Live view can be limited to reduce bandwidth consumption, for example if a slow connection is used between the AXIS Camera Station client and the AXIS Camera Station server.

When is audio available on a camera?

Audio is available if the camera has audio capabilities and audio has been enabled in the profile used for the live view.

Can Axis sign certificates?

If you use an existing CA and are not willing to allow AXIS Camera Station to sign the certificates on your behalf, you have to create the certificates outside of AXIS Camera Station and manually install them on devices.

image
A B C D E F G H I J K L M N O P Q R S T U V W X Y Z 1 2 3 4 5 6 7 8 9