Remote-access Guide

cisco asa 5505 remote access vpn configuration

by Einar Prohaska Published 2 years ago Updated 2 years ago
image

To configure the ASA5505, first log into it using the Cisco ASDM. Click the “Wizards” drop down, select “VPN Wizard.” Select “Remote Access,” click Next. Select “Pre-shared key,” then fill in what I’m going to call your “VPN Connection Password.” This will be saved in the client and should be as long and secure as possible.

To configure the ASA5505, first log into it using the Cisco ASDM. Click the “Wizards” drop down, select “VPN Wizard.”
...
Using the Cisco ASA 5505 as a VPN server with the Cisco VPN Client software
  1. Name: VPNUsers.
  2. Starting IP Address: 192.168. 15.194.
  3. Ending IP Address: 192.168. 15.220.
  4. Subnet Mask: 255.255. ...
  5. Click “OK.”
Jul 23, 2010

Full Answer

What is the maximum number of sessions for the ASA 5505?

For the ASA 5505, the maximum combined sessions is 10 for the Base license, and 25 for the Security Plus license. 2. A shared license lets the ASA act as a shared license server for multiple client ASAs.

How do I configure an ASA?

An ASA has at least two interfaces, referred to here as outside and inside. Typically, the outside interface is connected to the public Internet, while the inside interface is connected to a private network and is protected from public access. To begin, configure and enable two interfaces on the ASA. Then assign a name, IP address and subnet mask.

What are the licensing requirements for remote access IPsec VPNs?

Licensing Requirements for Remote Access IPsec VPNs Model License Requirement 1 ASA 5505 IPsec remote access VPN using IKEv2 (use ... ASA 5510 IPsec remote access VPN using IKEv2 (use ... ASA 5520 IPsec remote access VPN using IKEv2 (use ... ASA 5540 IPsec remote access VPN using IKEv2 (use ... 10 more rows ...

How do I assign an IPv4 or IPv6 address to AnyConnect?

You can configure the ASA to assign an IPv4 address, an IPv6 address, or both an IPv4 and an IPv6 address to an AnyConnect client by creating internal pools of addresses on the ASA or by assigning a dedicated address to a local user on the ASA.

image

How does Cisco remote access VPN Work?

Remote and mobile users use the Cisco AnyConnect Secure VPN client to establish VPN sessions with the adaptive security appliance. The adaptive security appliance sends web traffic to the Web Security appliance along with information identifying the user by IP address and user name.

How configure AnyConnect Cisco ASA?

5 Steps to Configure Cisco AnyConnect VPNConfigure AAA authentication. The first thing to configure is AAA authentication. ... Define VPN protocols. When users connect their VPN, they'll need an IP address for the VPN session. ... Configure tunnel groups. ... Set group policies. ... Apply the configuration. ... Authenticating logic flow.

How configure Cisco ASA site to site VPN?

1:0814:10Cisco ASA Site-to-Site VPN Configuration (Command Line)YouTubeStart of suggested clipEnd of suggested clipFirst of all we need to go into configuration mode so config T and now we're going to enable ISOMoreFirst of all we need to go into configuration mode so config T and now we're going to enable ISO camp on the outside interface that ISO camp is the handshake part of the configuration.

How do I access my Cisco ASA remotely?

There are eight basic steps in setting up remote access for users with the Cisco ASA.Configure an Identity Certificate.Upload the SSL VPN Client Image to the ASA.Enable AnyConnect VPN Access.Create a Group Policy.Configure Access List Bypass.Create a Connection Profile and Tunnel Group.Configure NAT Exemption.More items...•

How do I add VPN details to Cisco AnyConnect?

InstallUninstall any previous versions of Cisco AnyConnect.Install Cisco AnyConnect app from the Apple App Store or Google Play Store.Open the Cisco AnyConnect app.Select Add VPN Connection.Enter a Description, for example, CMU VPN and the Server Address vpn.cmu.edu.If prompted, allow the changes.Click Save.

Is Cisco AnyConnect IPsec or SSL?

Anyconnect is the replacement for the old Cisco VPN client and supports SSL and IKEv2 IPsec. When it comes to SSL, the ASA offers two SSL VPN modes: Clientless WebVPN.

How do I find my IPSec VPN in ASA?

Need to check how many tunnels IPSEC are running over ASA 5520....Please try to use the following commands.show vpn-sessiondb l2l.show vpn-sessiondb ra-ikev1-ipsec.show vpn-sessiondb summary.show vpn-sessiondb license-summary.and try other forms of the connection with "show vpn-sessiondb ?"

What is phase1 and Phase 2 in VPN?

Phase 1 Security Associations are used to protect IKE messages that are exchanged between two IKE peers, or security endpoints. Phase 2 Security Associations are used to protect IP traffic, as specified by the security policy for a specific type of traffic, between two data endpoints.

What is VPN type IKEv2?

IKEv2 (Internet Key Exchange version 2) is a VPN encryption protocol responsible for request and response actions. It handles the SA (security association) attribute within an authentication suite called IPSec.

What VPN types are supported by ASA?

For VPN Services, the ASA 5500 Series provides a complete remote-access VPN solution that supports numerous connectivity options, including Cisco VPN Client for IP Security (IPSec), Cisco Clientless SSL VPN, network-aware site-to-site VPN connectivity, and Cisco AnyConnect VPN client.

What is a network Asa?

The ASA in Cisco ASA stands for Adaptive Security Appliance. In brief, Cisco ASA is a security device that combines firewall, antivirus, intrusion prevention, and virtual private network (VPN) capabilities. It provides proactive threat defense that stops attacks before they spread through the network.

How do I upload images to ASA AnyConnect?

You need to upload the anyconnect client to the flash of the ASA. You can use the file management in the top menu of the ASA. Transfer the file from your local disc to the flash. Then select the image in Remote Access VPN - Network Client Access - Anyconnect Client Profile.

How do I get Cisco Anyconnect secure mobility client?

Open a web browser and navigate to the Cisco Software Downloads webpage.In the search bar, start typing 'Anyconnect' and the options will appear. ... Download the Cisco AnyConnect VPN Client. ... Double-click the installer.Click Continue.Go over the Supplemental End User License Agreement and then click Continue.More items...

How do I download Cisco Anyconnect from Asa?

Just load a new image to the ASA (under Configuration -> Remote-Access VPN -> Network (Client) Access -> AnyConnect Client Software) and the client will load the new software the next time when the client connects. Of course the client shouldn't have a setting applied to not download new software.

How do I upload images to ASA Anyconnect?

You need to upload the anyconnect client to the flash of the ASA. You can use the file management in the top menu of the ASA. Transfer the file from your local disc to the flash. Then select the image in Remote Access VPN - Network Client Access - Anyconnect Client Profile.

How do I disable Dtls in Asa?

Go to Configuration > Remote Access VPN > Network (client) Access > Group Policies. Edit the group policy. Then go to Advanced > Anyconnect Client. Here change the Datagram Transport Layer Security (DTLS) to Disable.

What is Cisco ASA 5505?

The Cisco ASA 5505, operating as an Easy VPN hardware client, supports management access using SSH or HTTPS, with or without a second layer of additional encryption. You can configure the Cisco ASA 5505 to require IPsec encryption within the SSH or HTTPS encryption.

Which interface has the highest security level?

In this scenario, the security appliance builds the tunnel only for vlan1, the interface with the highest security level. If you want to encrypt traffic from vlan12, you must change the security level of interface vlan1 to a lower value than that of vlan 12.

Can Cisco ASA 5505 be used as a VPN?

When configuring the Cisco ASA 5505 as an Easy VPN hardware client, you can specify a tunnel group or trustpoint configured on the Easy VPN server, depending on the Easy VPN server configuration. See the section that names the option you want to use:

Does Easy VPN use UDP?

By default, the Easy VPN hardware client and server encapsulate IPsec in User Datagram Protocol (UDP) packets. Some environments, such as those with certain firewall rules, or NAT and PAT devices, prohibit UDP. To use standard Encapsulating Security Protocol (ESP, Protocol 50) or Internet Key Exchange (IKE, UDP 500) in such environments, you must configure the client and the server to encapsulate IPsec within TCP packets to enable secure tunneling. If your environment allows UDP, however, configuring IPsec over TCP adds unnecessary overhead.

Can Cisco devices be used for authentication?

Devices such as Cisco IP phones, wireless access points, and printers are incapable of performing authentication . Enter the following command in global configuration mode to exempt such devices from authentication, thereby providing network access to them, if individual user authentication is enabled:

How many interfaces does an ASA have?

An ASA has at least two interfaces, referred to here as outside and inside. Typically, the outside interface is connected to the public Internet, while the inside interface is connected to a private network and is protected from public access.

What is the default LAN to LAN tunnel group?

There are two default tunnel groups in the ASA system: DefaultRAGroup, which is the default remote-access tunnel group, and DefaultL2Lgroup, which is the default LAN-to-LAN tunnel group. You can change them but not delete them. The ASA uses these groups to configure default tunnel parameters for remote access and LAN-to-LAN tunnel groups when there is no specific tunnel group identified during tunnel negotiation.

What is the first phase of ISAKMP?

Phase 1 creates the first tunnel to protect later ISAKMP negotiation messages. Phase 2 creates the tunnel that protects data travelling across the secure connection.

Is transparent mode supported in firewall?

Supported only in routed firewall mode. Transparent mode is not supported.

Do you need a mask for a VPN?

The address mask is optional. However, You must supply the mask value when the IP addresses assigned to VPN clients belong to a non-standard network and the data could be routed incorrectly if you use the default mask. A typical example is when the IP local pool contains 10.10.10.0/255.255.255.0 addresses, since this is a Class A network by default. This could cause routing issues when the VPN client needs to access different subnets within the 10 network over different interfaces.

How many interfaces does an ASA have?

An ASA has at least two interfaces, referred to here as outside and inside. Typically, the outside interface is connected to the public Internet, while the inside interface is connected to a private network and is protected from public access.

What is the default LAN to LAN tunnel group?

There are two default tunnel groups in the ASA system: DefaultRAGroup, which is the default remote-access tunnel group, and DefaultL2Lgroup, which is the default LAN-to-LAN tunnel group. You can change them but not delete them. The ASA uses these groups to configure default tunnel parameters for remote access and LAN-to-LAN tunnel groups when there is no specific tunnel group identified during tunnel negotiation.

What is the first phase of ISAKMP?

Phase 1 creates the first tunnel to protect later ISAKMP negotiation messages. Phase 2 creates the tunnel that protects data travelling across the secure connection.

Is IPv6 supported for SSL?

Assigning an IPv6 address to the client is supported for the SSL protocol. This feature is not supported for the IKEv2/IPsec protocol.

Do you need a mask for a VPN?

The address mask is optional. However, You must supply the mask value when the IP addresses assigned to VPN clients belong to a non-standard network and the data could be routed incorrectly if you use the default mask. A typical example is when the IP local pool contains 10.10.10.0/255.255.255.0 addresses, since this is a Class A network by default. This could cause routing issues when the VPN client needs to access different subnets within the 10 network over different interfaces.

Is transparent mode supported in firewall?

Supported only in routed firewall mode. Transparent mode is not supported.

Can ASA assign IPv4 and IPv6?

You can configure the ASA to assign an IPv4 address, an IPv6 address, or both an IPv4 and an IPv6 address to an AnyConnect client by creating internal pools of addresses on the ASA or by assigning a dedicated address to a local user on the ASA.

image
A B C D E F G H I J K L M N O P Q R S T U V W X Y Z 1 2 3 4 5 6 7 8 9