Remote-access Guide

cisco asa 5510 remote access vpn configuration example

by Carolyne Bechtelar Sr. Published 2 years ago Updated 2 years ago
image

What is Cisco ASA remote access VPN?

Cisco ASA Remote Access VPN. The remote user requires the Cisco VPN client software on his/her computer, once the connection is established the user will receive a private IP address from the ASA and has access to the network. The Cisco VPN client is end-of-life and has been replaced by the Cisco Anyconnect Secure Mobility Client.

How do I connect to the ASA from another computer?

This allows remote users to connect to the ASA and access the remote network through an IPsec encrypted tunnel. The remote user requires the Cisco VPN client software on his/her computer, once the connection is established the user will receive a private IP address from the ASA and has access to the network.

How to use clientless WebVPN with Asa?

The clientless WebVPN method does not require a VPN client to be installed on the user’s computer. You just open your web browser, enter the IP address of the ASA and you will get access through a web portal. You only have limited access to a number of applications, for example: There is no full network access when you use clientless WebVPN.

Is there a basic configuration tutorial for the Cisco ASA 5510security appliance?

I’m offering you here a basic configuration tutorial for the Cisco ASA 5510security appliance but the configuration applies also to the other ASA models as well (see also this Cisco ASA 5505 Basic Configuration).

image

How do I access my Cisco ASA remotely?

There are eight basic steps in setting up remote access for users with the Cisco ASA.Configure an Identity Certificate.Upload the SSL VPN Client Image to the ASA.Enable AnyConnect VPN Access.Create a Group Policy.Configure Access List Bypass.Create a Connection Profile and Tunnel Group.Configure NAT Exemption.More items...•

How do I enable VPN on ASA?

Set up VPN on a Cisco ASA deviceOpen ASDM.Go to Wizards VPN Wizards. IPsec (IKEv1) Remote Access VPN Wizard.Bypass the interface access lists: ... Click Next.Choose Microsoft Windows client using L2TP over IPsec and check the box for MS-CHAP-V2.Click Next.Authenticate the machine: ... Click Next.More items...

How does Cisco remote access VPN Work?

Remote and mobile users use the Cisco AnyConnect Secure VPN client to establish VPN sessions with the adaptive security appliance. The adaptive security appliance sends web traffic to the Web Security appliance along with information identifying the user by IP address and user name.

How do I allow VPN through Cisco firewall?

SolutionCreate a Static (One-To-One) NAT so that the ASA that has a private IP on its outside interface, (192.168. ... Allow UDP 500 (ISAKMP) from the ASA (1.1. ... Allow UDP 4500 (NAT-TRAVERSAL) from the ASA (1.1. ... Allow UDP 500 (ISAKMP) from the ASA (192.168. ... Allow UDP 4500 (NAT-TRAVERSAL) from the ASA (192.168.

How is Cisco VPN configured?

Steps for setting up a VPNStep 1: Line up key VPN components. ... Step 2: Prep devices. ... Step 3: Download and install VPN clients. ... Step 4: Find a setup tutorial. ... Step 5: Log in to the VPN. ... Step 6: Choose VPN protocols. ... Step 7: Troubleshoot. ... Step 8: Fine-tune the connection.

How do I setup a Cisco VPN?

InstallUninstall any previous versions of Cisco AnyConnect.Install Cisco AnyConnect app from the Apple App Store or Google Play Store.Open the Cisco AnyConnect app.Select Add VPN Connection.Enter a Description, for example, CMU VPN and the Server Address vpn.cmu.edu.If prompted, allow the changes.Click Save.

Does Cisco AnyConnect use SSL or IPsec?

Anyconnect is the replacement for the old Cisco VPN client and supports SSL and IKEv2 IPsec. When it comes to SSL, the ASA offers two SSL VPN modes: Clientless WebVPN.

How do I setup a VPN server?

Android:Tap the Settings icon.Tap Network & internet.Tap Advanced.Tap VPN.Tap Add.Enter the information including Name, Type, Server Address, Username, and Password.Tap Save.Again, tap the Settings icon.More items...•

Is Cisco AnyConnect a VPN?

Cisco AnyConnect Client helps us to make secure , safe and reliable VPN connection to our organization's private network with multiple security services to safe and protect company's data. It gives freedom to employees to get connected from anywhere anytime, thus making life easier for remote workers.

How do I configure IPsec on ASA firewall?

ProcedureTo set the connection type to IPsec LAN-to-LAN, enter the tunnel-group command. ... To set the authentication method to use a preshared key, enter the ipsec-attributes mode and then enter the ikev1pre-shared-key command to create the preshared key. ... Save your changes.

How can I check my Cisco ASA VPN status?

Please try to use the following commands.show vpn-sessiondb l2l.show vpn-sessiondb ra-ikev1-ipsec.show vpn-sessiondb summary.show vpn-sessiondb license-summary.and try other forms of the connection with "show vpn-sessiondb ?"

How do I enable ikev2 on Cisco ASA?

Configure the remote IPsec tunnel pre-shared key or certificate trustpoint. Create a crypto map and match based on the previously created ACL....IPsec IKEv2 Example.1Create and enter IKEv2 policy configuration mode.asa1(config)#crypto ikev2 policy 12Configure an encryption method.asa1(config-ikev2-policy)#encryption aes17 more rows•Nov 15, 2013

Does Cisco AnyConnect work anywhere?

Cisco AnyConnect Secure Mobility Client empowers employees to work from anywhere on company laptops or personal mobile devices. It also provides the visibility and control security teams need to identify who and which devices are accessing their infrastructure.

What protocol does Cisco VPN use?

Cisco AnyConnect VPNs utilize TLS to authenticate and configure routing, then DTLS to efficiently encrypt and transport the tunneled VPN traffic, and can fall back to TLS-based transport where firewalls block UDP-based traffic.

How does Palo Alto VPN Work?

How Does VPN Work? A VPN creates a private connection, known as a “tunnel,” to the internet. All information travelling from a device connected to a VPN will get encrypted and go through this tunnel. When connected to a VPN, a device will behave as if it's on the same local network as the VPN.

How do I connect to ASU VPN?

Open the “Cisco AnyConnect Secure Mobility Client”. Give the vpn server address as “sslvpn.asu.edu/2fa” and click on connect. 2. Then use your ASURITE User ID and Password, click on OK you will be connected to VPN.

How many interfaces does an ASA have?

An ASA has at least two interfaces, referred to here as outside and inside. Typically, the outside interface is connected to the public Internet, while the inside interface is connected to a private network and is protected from public access.

What is the default LAN to LAN tunnel group?

There are two default tunnel groups in the ASA system: DefaultRAGroup, which is the default remote-access tunnel group, and DefaultL2Lgroup, which is the default LAN-to-LAN tunnel group. You can change them but not delete them. The ASA uses these groups to configure default tunnel parameters for remote access and LAN-to-LAN tunnel groups when there is no specific tunnel group identified during tunnel negotiation.

What is the first phase of ISAKMP?

Phase 1 creates the first tunnel to protect later ISAKMP negotiation messages. Phase 2 creates the tunnel that protects data travelling across the secure connection.

Do you need a mask for a VPN?

The address mask is optional. However, You must supply the mask value when the IP addresses assigned to VPN clients belong to a non-standard network and the data could be routed incorrectly if you use the default mask. A typical example is when the IP local pool contains 10.10.10.0/255.255.255.0 addresses, since this is a Class A network by default. This could cause routing issues when the VPN client needs to access different subnets within the 10 network over different interfaces.

What is AnyConnect VPN?

Anyconnect is the replacement for the old Cisco VPN client and supports SSL and IKEv2 IPsec. When it comes to SSL, the ASA offers two SSL VPN modes: Clientless WebVPN. AnyConnect VPN. The clientless WebVPN method does not require a VPN client to be installed on the user’s computer. You just open your web browser, ...

When remote users connect to our WebVPN, do they have to use HTTPS?

The following option is not required but useful, whenever someone accesses the ASA through HTTP then they will be redirected to HTTPS:

What happens when a VPN user terminates a session?

Normally when the remote VPN user terminates the session, the anyconnect installer will be uninstalled. The anyconnect keep-installer installed command leaves it installed on the user’s computer.

What happens when you have an inbound access list?

When you have an inbound access-list on the outside interface then all your decrypted traffic from the SSL WebVPN has to match the inbound access-list. You can either create some permit statements for the decrypted traffic or you can just tell the ASA to let this traffic bypass the access-list:

Why does my client tries to download AnyConnect?

The client tries to download the Anyconnect automatically, this is because of the anyconnect ask none default anyconnect command that we used. Since we are using a self-signed certificate you will get the following error message:

What is the IP address of AnyConnect?

You can see that we received IP address 192.168.10.100 (the first IP address from the VPN pool). Anyconnect creates an additional interface, just like the legacy Cisco VPN client does.

What is an ayconnECT_policy?

The group policy is called “ANYCONNECT_POLICY” and it’s an internal group policy which means that we configure it locally on the ASA. An external group policy could be on a RADIUS server.

How many interfaces does an ASA have?

The ASA has two interfaces: inside and outside. Imagine the outside interface is connected to the Internet where a remote user wants to connect to the ASA. On the inside we find R1, I will only use this router so the remote user has something to connect to on the inside network. Let’s look at the configuration!

What is VPN_POLICY?

The group policy is called VPN_POLICY and it’s an internal group policy which means it is created locally on the ASA. You can also specify an external group policy on a RADIUS server. I added some attributes, for example a DNS server and an idle timeout (15 minutes). Split tunneling is optional but I added it to show you how to use it, it refers to the access-list we created earlier.

Does Cisco VPN require ASA?

The remote user requires the Cisco VP N client software on his/her computer, once the connection is established the user will receive a private IP address from the ASA and has access to the network .

Can remote VPN users access certain networks?

If you want to configure an access-list so the remote VPN users can only reach certain networks , IP addresses or ports then you can apply this under the group policy.

Can you use VPN on remote network?

If you don’t want this then you can enable split tunneling. With split tunneling enabled, we will use the VPN only for access to the remote network. Here’s how to enable it:

image
A B C D E F G H I J K L M N O P Q R S T U V W X Y Z 1 2 3 4 5 6 7 8 9