To add a static route, enter the following command: hostname (config)# route if_name dest_ip mask gateway_ip [ distance ]
Full Answer
What is a default route in Cisco ASA?
A default route identifies the gateway IP address to which the ASA sends all IP packets for which it does not have a learned or static route. A default static route is simply a static route with 0.0.0.0/0 as the destination IP address.
How do I route Asa traffic to a nonconnected host?
To route traffic to a nonconnected host or network, you must define a static route to the host or network or, at a minimum, a default route for any networks to which the ASA is not directly connected; for example, when there is a router between a network and the ASA.
How does the ASA distribute traffic among gateways?
The ASA distributes the traffic among the specified gateways. A default route identifies the gateway IP address to which the ASA sends all IP packets for which it does not have a learned or static route.
How to set up SSL VPN on ASA?
ASA that runs on version 8.x Cisco SSL VPN Client (SVC) 1.x Note: Download the SSL VPN Client package (sslclient-win*.pkg) from Cisco Software Download ( registered customers only) . Copy the SVC to the flash memory on the ASA. The SVC needs to be downloaded to the remote user computers in order to establish the SSL VPN connection with the ASA.
How do I add a static route in ASA firewall?
Static Route Configuration:ASA(config)# route [interface name] [destination address] [netmask] [gateway]! First configure a default static route towards the default gateway. ASA(config)# route outside 0.0.0.0 0.0.0.0 200.1.1.1.! Then configure an internal static route to reach network LAN2.
How do you assign a static route?
Configuring Static RoutesNavigate to the Configuration > Network > IP > IP Routes page.Click Add to add a static route to a destination network or host. Enter the destination IP address and network mask (255.255. ... Click Done to add the entry. Note that the route has not yet been added to the routing table.
How do I set a static IP route Cisco?
Perform these steps to configure a default route.Enter global configuration mode. device# configure terminal.Enter 0.0. 0.0 0.0. ... (Optional) Enable the default network route for static route next-hop resolution. ... (Optional) Configure next-hop recursive lookup to resolve the next-hop gateway.
How do you configure a default route on an ASA?
Configure a Default Route A default route is simply a static route with 0.0. 0.0/0 as the destination IP address. ASA would be configured using the command route {nameif}.
What does IP route 0.0 0.0 0.0 0.0 mean?
In the Internet Protocol Version 4, the address 0.0. 0.0 is a non-routable meta-address used to designate an invalid, unknown or non-applicable target. This address is assigned specific meanings in a number of contexts, such as on clients or on servers.
How do I assign an IP address to a route?
The easiest way to add a route on Linux is to use the “ip route add” command followed by the network address to be reached and the gateway to be used for this route. By default, if you don't specify any network device, your first network card, your local loopback excluded, will be selected.
Which command will create a static route?
The 'ip route' command is a global configuration command. This command defines a static route for a specific destination network.
Which command will add a static route to the router?
To establish static routes, use the ip route command in switch configuration mode.
What is a directly connected static route?
A directly attached, or directly connected static route, uses the exit interface to forward traffic to the intended destination. This is in contrast to the recursive static route which used the next hop IP address of the router along the path to the destination.
How do I assign an IP address to a firewall in Asa?
Set a Static IP for your Cisco ASA5505 FirewallOpen the ASDM and log into your device.Under Configuration, Interfaces, select the Outside interface and hit Edit.In the 'IP Address' box, click the radio for 'Use Static IP'Select an IP address, and use '255.255. ... Hit ok, then apply.More items...•
How configure Cisco ASA management IP?
In order to enable the Management 1/1 interface to act as a normal Firewall interface, use the following configuration:ASA(config)# interface Management 1/1. ASA(config-if)# no management-only.! Enable local authentication for SSH access: ... !
What is the command to enable HTTP on ASA?
0:001:31Cisco ASA ver. 6, 7, and 8.2: HTTP enable commands - YouTubeYouTubeStart of suggested clipEnd of suggested clipLet Cisco a SI or a pix the HTTP command allows us to basically enable the HTTP server so we can getMoreLet Cisco a SI or a pix the HTTP command allows us to basically enable the HTTP server so we can get into the GUI.
How do I add a static route in Windows?
To add a route:Type route add 0.0. 0.0 mask 0.0. 0.0
How do I add a static route in Linux?
Add a static route on Linux$ su - OR use the sudo as follows:$ sudo -i. Once become a root user, setup a temporary route using the ip command:# ip route add 172.10.1.0/24 via 10.0.0.100 dev eth0. Verify new routing table, enter:# ip r. ... # ip link set dev tun0 up mtu 1500. ... # ip r.
What is static route example?
Static routes are created in global config mode, and require a destination prefix and a way to get there. For example, let's say that our router's Serial 1/1 interface, with an IP address of 192.168. 1.5/30, has a point-to-point link to another router's Serial 2/2, with IP address 192.168. 1.6/30.
Which command will add a static route to the router?
To establish static routes, use the ip route command in switch configuration mode.
How does ASA work?
The ASA implements this feature by associating a static route with a monitoring target that you define, and monitors the target using ICMP echo requests. If an echo reply is not received within a specified time period, the object is considered down and the associated route is removed from the routing table. A previously configured backup route is used in place of the removed route.
Why are static routes removed from the routing table?
Static routes are only removed from the routing table if the associated interface on the ASA goes down.
What is static route?
Information About Static and Default Routes. To route traffic to a nonconnected host or network, you must define a static route to the host or network or, at a minimum, a default route for any networks to which the ASA is not directly connected; for example, when there is a router between a network and the ASA.
What is a default route?
A default route identifies the gateway IP address to which the ASA sends all IP packets for which it does not have a learned or static route. A default static route is simply a static route with 0.0.0.0/0 as the destination IP address. Routes that identify a specific destination take precedence over the default route.
What is the default administrative distance for routes discovered by OSPF?
The default administrative distance for routes discovered by OSPF is 110. If a static route has the same administrative distance as a dynamic route, the static route takes precedence. Connected routes always take precedence over static or dynamically discovered routes.
What is the distance argument in a routing protocol?
The distance argument is the administrative distance for the route. The default is 1 if you do not specify a value. Administrative distance is a parameter used to compare routes among different routing protocols. The default administrative distance for static routes is 1, giving it precedence over routes discovered by dynamic routing protocols but not directly connected routes.
What is the difference between dest_ip and gateway_ip?
The dest_ip and mask arguments indicate the IP address for the destination network, and the gateway_ip argument is the address of the next-hop router. The addresses you specify for the static route are the addresses that are in the packet before entering the ASA and performing NAT.
What does it mean when you see a packet with source as VPN client interface reaching the inside interface for the destination of?
-If you see packet with source as VPN client interface reaching the inside interface for the destination of host behind the ASA , then its an issue with your internal routing.
Is Cisco hosting the IT Blog Awards 2021?
The 2021 IT Blog Awards, hosted by Cisco, is now open for submissions. Submit your blog, vlog or podcast today. For more information, including category details, the process, past winners and FAQs, check out: https://www.cisco.com/c/en/us/t... view more
What does TDG do after routing packets?
After the packets are routed to the TDG, which is Router 2 in this case, it performs the address translation to route those packets ahead to the Internet. For more information on configuring a router as an Internet Gateway, refer to How to Configure a Cisco Router Behind a Non-Cisco Cable Modem.
What does VPN-sessiondb svc do?
show VPN-sessiondb svc —Displays the information about the current SSL connections.
Can you observe additional configuration in CLI?
In the CLI, you can observe some additional configuration. The complete CLI configuration is shown below and important commands have been highlighted.
Introduction
Prerequisites
- Requirements
Ensure that you meet these requirements before you attempt this configuration: 1. ASA that runs on version 8.x 2. Cisco SSL VPN Client (SVC) 1.x Note: Download the SSL VPN Client package (sslclient-win*.pkg) from Cisco Software Download (registeredcustomers only) . Copy the SVC t… - Components Used
The information in this document is based on these software and hardware versions: 1. Cisco 5500 Series ASA that runs software version 8.x 2. Cisco SSL VPN Client version for Windows 1.1.4.179 3. PC that runs Windows 2000 Professional or Windows XP 4. Cisco Adaptive Securit…
Background Information
- The SSL VPN Client (SVC) is a VPN tunneling technology that gives remote users the benefits of an IPSec VPN client without the need for network administrators to install and configure IPSec VPN clients on remote computers. The SVC uses the SSL encryption that is already present on the remote computer as well as the WebVPN login and authentication of the Security Appliance…
Configure
- In this section, you are presented with the information to configure the features described in this document. Note: Use the Command Lookup Tool (registeredcustomers only) to obtain more information on the commands used in this section.
Verify
- The commands given in this section can be used to verify this configuration. The Output Interpreter Tool (registered customers only) (OIT) supports certain show commands. Use the OIT to view an analysis of showcommand output. 1. show webvpn svc——Displays the SVC images stored in the ASA flash memory. 2. show VPN-sessiondb svc—Displays the information about th…
Related Information