STEP 1From the Cisco ISA500 Configuration Utility, click VPN> IPsec Remote Access. The IPsec Remote Access window appears. STEP 2Click Onto enable IPsec Remote Access, or click Offto disable it.
Full Answer
How do remote access clients connect to Asa?
As remote access clients connect to the ASA, they connect to a connection profile, which is also known as a tunnel group. We’ll use this tunnel group to define the specific connection parameters we want them to use.
What does it mean to configure a Cisco switch?
Configuring a Cisco switch properly means your network can make connections efficiently. In this step-by-step guide, we walk you through configuring Cisco switches and look at some FAQs.
What certificates do I need for mobile and remote access access access policy?
The minimum Expressway release for Mobile and Remote Access Access Policy support with Cisco Jabber is X8.10. You must exchange certificates between Unified Communications Manager, the IM and Presence Service, and Cisco Expressway-C. Cisco recommends that you use CA-signed certificates with the same CA for each system. In this case:
What is setup utility in Cisco router?
It is a step-by-step guide for the most basic configuration commands needed to make the router operational. When you first power up a new Cisco Router, you have the option of using the “setup” utility which allows you to create a basic initial configuration.
How to connect to Cisco router?
For the first time when the device is not configured yet, you usually connect directly with a console cable via the CON port. The console cable connection is also called “out of band” connection method.
What is the setup utility for Cisco router?
When you first power up a new Cisco Router, you have the option of using the “setup” utility which allows you to create a basic initial configuration.
What is global configuration mode?
In Global Configuration Mode you configure parameters that affect the whole router device. Here we will configure the Enable Secret password that you will be using from now own to enter into Privileged EXEC Mode from User EXEC Mode.
How to differentiate router from other devices?
To differentiate your Router from other devices in the network, you should configure a Hostname for your device.
What does "show running configuration" mean?
When you issue the “ show running-configuration ” command on the router you instruct the device to display the current running configuration in RAM. When you issue the “ show startup-configuration ” command you instruct the router to display the stored configuration in the NVRAM.
What is the default static route?
The default static route above instructs the router to send ALL packets that the router does not have a more specific route entry to gateway address 100.100.100.2 (which might be the ISP gateway address).
What is the most basic parameter for a router interface?
This is an essential step in order for your router to be able to forward packets in the network. The most basic parameter for a Router Interface is the IP address. From Global Configuration Mode you need to enter into Interface Configuration Mode:
How do I set a static IP on a Cisco switch?
A problem with the GUI interface of Cisco switches makes it impossible to assign a static IP address to an interface. Follow these steps for a workaround:
What does it mean to configure a Cisco switch?
Configuring a Cisco switch properly means your network can make connections efficiently. In this step-by-step guide, we walk you through configuring Cisco switches and look at some FAQs.
What is a default gateway?
The default gateway is essentially the address of the router that the switch will be communicating with. If you don’t configure a default gateway then VLAN1 will be unable to send traffic to another network. To assign the default gateway, enter the command below (change the IP address to that of your router).
How to make a switch easier to locate?
You can make the switch easier to locate in the network by assigning a hostname. Enter the following command to assign a hostname: Switch (config)# hostname access-switch1 access-switch1 (config)#1. 3. Assign a Password to the Switch.
How many pins does a switch need to be connected to PuTTY?
Connect the switch to PuTTY with a 9-pin serial cable.
How to connect a switch to putty?
1. Connect the Switch to PuTTY. To start configuration, you want to connect the switch console to PuTTY. You can do this by doing the following: Connect the switch to PuTTY with a 9-pin serial cable.
What is the role of switches in 2021?
When we think of connectivity in a network, the router is probably the first device that comes to mind, but switches play a vital role in enabling network devices to communicate. Switches can take incoming/outgoing traffic and pass it onward toward its final destination.
What is MRA access policy?
For Cisco Jabber users, the MRA access policy that you configured must be associated to your Cisco Jabber users during the LDAP sync. For information on how to provision end users, see the End User Configuration .
What is off-premises access?
Off-premises access: a consistent experience outside the network for Jabber and EX/MX/SX Series clients
Does Cisco Expressway use Unified Communications Manager?
This feature requires you to integrate Unified Communications Manager with Cisco Expressway. For Cisco Expressway configuration details for Mobile and Remote Access, refer to the Mobile and Remote Access Through Cisco Expressway Deployment Guide .
Do you need to exchange certificates between Cisco Expressway and Unified Communications Manager?
Cisco recommends that you use CA-signed certificates with the same CA for each system. In this case:
Do you need NTP for mobile access?
Mobile and Remote Access requires that you set up NTP servers for your deployment. Make sure that you have NTP servers deployed for your network and Phone NTP References for SIPendpoints.
Does Expressway C use forward and reverse DNS?
You must create internal DNS records, for both forward and reverse lookups, for all Unified Communications nodes used with Mobile and Remote Access. This allows Expressway-C to find the nodes when IP addresses or hostnames are used instead of FQDNs. Make sure that the SRV record is not resolvable outside of the local network.
Does Ice use a turn server?
As a fallback mechanism, ICE can use a TURN server to relay media. Make sure that you have deployed a TURN server.