STEP 1From the Cisco ISA500 Configuration Utility, click VPN> IPsec Remote Access. The IPsec Remote Access window appears. STEP 2Click Onto enable IPsec Remote Access, or click Offto disable it.
Full Answer
How do I set up remote access with Cisco ASA?
There are eight basic steps in setting up remote access for users with the Cisco ASA. Step 1. Configure an Identity Certificate Step 2. Upload the SSL VPN Client Image to the ASA Step 3. Enable AnyConnect VPN Access Step 4. Create a Group Policy Step 5. Configure Access List Bypass Step 6.
How to configure a Cisco routers?
Step-by-Step Configuration of Cisco Routers Step1: Configure Access Passwords Step2: Configure a Router Hostname Step3: Configure IP addresses for Router Interfaces Step4: Configure Routing (Static or Dynamic) Step5: Save your configuration
What is setup utility in Cisco router?
It is a step-by-step guide for the most basic configuration commands needed to make the router operational. When you first power up a new Cisco Router, you have the option of using the “setup” utility which allows you to create a basic initial configuration.
How to disable flow control on the 300 and 500 series switches?
For 300 and 500 Series Managed Switches, this is 115200. Go to the Data bits field and enter 8. Now go to the Stops bits field and enter 1. Click on the Parity drop-down menu and select the None option. Go to the Flow Control drop-down menu and select the None option.
What is the setup utility for Cisco router?
When you first power up a new Cisco Router, you have the option of using the “setup” utility which allows you to create a basic initial configuration.
How to connect to Cisco router?
For the first time when the device is not configured yet, you usually connect directly with a console cable via the CON port. The console cable connection is also called “out of band” connection method.
What is global configuration mode?
In Global Configuration Mode you configure parameters that affect the whole router device. Here we will configure the Enable Secret password that you will be using from now own to enter into Privileged EXEC Mode from User EXEC Mode.
How to differentiate router from other devices?
To differentiate your Router from other devices in the network, you should configure a Hostname for your device.
What is a ROM on a router?
ROM: This is where the POST script of the router is located. The POST software (Power On Self Test) is used during startup to perform the initial hardware checking of the device. The ROM also holds a mini-IOS used for password recovery.
What does "show running configuration" mean?
When you issue the “ show running-configuration ” command on the router you instruct the device to display the current running configuration in RAM. When you issue the “ show startup-configuration ” command you instruct the router to display the stored configuration in the NVRAM.
What is the default static route?
The default static route above instructs the router to send ALL packets that the router does not have a more specific route entry to gateway address 100.100.100.2 (which might be the ISP gateway address).
How do I set a static IP on a Cisco switch?
A problem with the GUI interface of Cisco switches makes it impossible to assign a static IP address to an interface. Follow these steps for a workaround:
What does it mean to configure a Cisco switch?
Configuring a Cisco switch properly means your network can make connections efficiently. In this step-by-step guide, we walk you through configuring Cisco switches and look at some FAQs.
What is a default gateway?
The default gateway is essentially the address of the router that the switch will be communicating with. If you don’t configure a default gateway then VLAN1 will be unable to send traffic to another network. To assign the default gateway, enter the command below (change the IP address to that of your router).
How to make a switch easier to locate?
You can make the switch easier to locate in the network by assigning a hostname. Enter the following command to assign a hostname: Switch (config)# hostname access-switch1 access-switch1 (config)#1. 3. Assign a Password to the Switch.
How many pins does a switch need to be connected to PuTTY?
Connect the switch to PuTTY with a 9-pin serial cable.
How to connect a switch to putty?
1. Connect the Switch to PuTTY. To start configuration, you want to connect the switch console to PuTTY. You can do this by doing the following: Connect the switch to PuTTY with a 9-pin serial cable.
What is the role of switches in 2021?
When we think of connectivity in a network, the router is probably the first device that comes to mind, but switches play a vital role in enabling network devices to communicate. Switches can take incoming/outgoing traffic and pass it onward toward its final destination.
