Configure Web Access Management on SPA122
- Log in to the Phone Adapter Configuration Utility and choose Administration > Management > Web Access Management.
- Click Enabled to enable web access management for Admin Access or click Disabled to disable web access...
- In the Web Utility Access field, check the method (s) that you would like to use to access the Phone Adapter...
- Click Enabled to enable remote access, or click Disabled to disable remote access. Skip to Step 9 if you chose...
How do I configure the spa122 for remote access?
Click the Any IP Address radio button to allow any remote IP address to configure the SPA122. Click the radio button directly below the Any IP Address radio button to only allow a single IP address or a range of addresses to remotely access the SPA122. Enter the IP address or range in the corresponding field. Step 8.
How do I configure the Cisco SPA112 configuration utility?
Use the Administration > Management > Web Access Management page to configure the settings for access to the administration of the ATA. Access to the Cisco SPA112 configuration utility is enabled by default.
Can I configure the spa122 using the default static IP address?
Connecting the SPA122 directly to my PC did allow me to configure the device using the default static IP address. However, after attaching it to my network, the web GUI was still not accessible, even with Web admin access enabled. Also, the interactive voice response (IVR) does not allow changing of WAN access using code 7932.
Which WAN port does the spa122 use?
The SPA122 is SPA112 (ATA) bundled with router. If I understood your network topology, you need no router, so you will use just WAN port (the blue one, labeled 'Internet') of the SPA122. This port needs to be connected to Netcomm.
How do I log into my Cisco SPA 122?
ProcedureUsing a LAN/Ethernet cable, connect the computer to the yellow Ethernet (LAN) port of the SPA122.Open Internet Explorer browser (IE is required to ensure the adapter's configuration page displays properly).Log in: admin / (administrator password)Click Voice > Provisioning.Click Submit.More items...•
How do I log into my Cisco SPA 112?
How to access the web configuration utility on the Cisco SPA112Open a web browser and enter the IP address of the phone adapter in the address bar, then press Enter.Enter the username of the device in the Username field. ... Enter the password of the device in the Password field.More items...
How do I reset my Cisco SPA 122?
RESET — Press the Reset button to restart the SPA122 device. To restore it to factory default settings, hold the button for 20 seconds.
How do I log into my network configuration utility?
To open the web-based configuration utility: Open a Web browser. Enter the IP address of the WAP device that you are configuring in the address bar on the browser, and then press Enter. The Login page opens.
How do I log into ATA?
Enter this IP address into your browser 192.168. 15.1 to be prompted for login. Log in to the device using the default (case-sensitive) username ("admin") and password ("admin"), and then click Log In. Navigate to Administration tab.
How do I reset my Cisco phone adapter?
Factory reset your Cisco SPA112 Hold the reset button down for 30s, or until the power LED light begins to flash again. Release the button. Allow the device to boot up; it may take 2-5 minutes for the reset process to complete. The power LED light will stop flashing once it has initialized.
How do I find the IP address of my Cisco spa122?
At the voice prompt menu, enter 110 #. The phone will read back the IP address of the base, which can be entered into a browser to access the configuration. At the voice prompt menu, enter 210 #. The phone will read back the IP address of the base, which can be entered into a browser to access the configuration.
What does a Cisco ATA do?
Your analog telephone adapter (ATA) allows you to connect an analog device, such as an analog phone or fax machine, to your network. The connected device can then function like the IP phones in your network.
What is Cisco SPA100?
Cisco SPA100 and SPA200 Series ATAs are intended for high-volume deployments by VoIP service providers to residential and small business customers . In business or enterprise environments, these ATAs can serve as terminal nodes. These devices are widely distributed across the Internet, connected through routers and firewalls at the customer premises. The IP Telephony device can be used as a remote extension of the service provider back-end equipment. Remote management and configuration ensures the proper operation of the IP Telephony device at the customer premises. This customized, ongoing configuration is supported by the following features: • Reliable remote control of the endpoint • Encryption of the communication controlling the endpoint • Streamlined endpoint account binding This chapter describes the features and functionality available when provisioning these ATAs and explains the setup required: • Deployment, page 6 • Provisioning Overview, page 8
How does Cisco ATA work?
In a retail distribution model, a customer purchases a Cisco ATA and subscribes to a particular service. The Internet Telephony Service Provider (ITSP) sets up and maintains a provisioning server, and preprovisions the phone to resynchronize with the service provider server. See In-House Device Preprovisioning, page 37 for more information. The customer signs on to the service and establishes a VoIP account, possibly through an online portal, and binds the device to the assigned service account. When the device is powered up or a specified time elapses, the IP Telephony device resynchronizes, downloading the latest parameters. These parameters can address goals such as setting up a hunt group, setting speed dial numbers, and limiting the features that a user can modify.
What is the DHCP address for Supervoip?
In this example, a device at the DHCP-assigned IP address 192.168.1.102 is instructed to provision itself to the SuperVoIP service at prov.supervoip.com. The remote provisioning server is configured to associate the ATA that is performing the resync request with the new account, based on the config file spa.cfg. Through this initial resync operation, the ATA is configured in a single step, and is automatically directed to resync thereafter to a permanent URL on the server. For both initial and permanent access, the provisioning server relies on the client certificate for authentication and supplies configuration parameter values based on the associated service account.
What is an ATA firmware?
The firmware for each ATA includes an ad ministration web server that accepts new configuration parameter values. The ATA is instructed to resync with a specified provisioning server through a resync URL command. For example:
Why is IP telephony only used when the IP phone is idle?
By default, a profile resync is only attempted when the IP Telephony device is idle, because the upgrade might trigger a software reboot interrupting a call. If intermediate upgrades are required to reach a current upgrade state from an older release, the upgrade logic is capable of automating multi-stage upgrades.
What is a Cisco service provider?
The service provider works with a Cisco sales engineer to develop a simple provisioning profile. The profile contains minimal information that redirects the device to the service provider provisioning server. This profile is placed on the Cisco RC server by the Cisco Voice Team.
How to secure a configuration profile?
A configuration profile can be encrypted by using symmetric key encryption, whether or not the file is compressed. The supported encryption algorithm is the American Encryption Standard (AES), using 256-bit keys, applied in cipher block chaining mode.
How to reset ATA?
Use the Administration > Factory Defaults page to reset the ATA to the default configuration. Alternatively, press and hold the RESET button for 20 seconds. All user-changeable non-default settings will be lost. This may include network and service provider data.
What is TR-069?
Use the Administration > Management > TR-069 page to configure communication with an Auto-Configuration Server (ACS) via TR-069 CPE WAN Management Protocol (CWMP). TR-069 (Technical Report 069) provides a common platform to manage all voice devices and other customer-premises equipment (CPE) in large-scale deployments. It provides the communication between the CPE and the ACS.
