Remote-access Guide

cisco spa122 remote access

by Aiyana Little Published 2 years ago Updated 2 years ago
image

Configure Web Access Management on SPA122

  1. Log in to the Phone Adapter Configuration Utility and choose Administration > Management > Web Access Management.
  2. Click Enabled to enable web access management for Admin Access or click Disabled to disable web access...
  3. In the Web Utility Access field, check the method (s) that you would like to use to access the Phone Adapter...
  4. Click Enabled to enable remote access, or click Disabled to disable remote access. Skip to Step 9 if you chose...

Full Answer

How do I configure Web Access Management on a spa122?

The objective of this article is to explain how to configure web access management on a SPA122. Step 1. Log in to the Phone Adapter Configuration Utility and choose Administration > Management > Web Access Management. The Web Access Management page opens:

How do I connect my phone to the spa122 via Ethernet?

Temporarily connect your computer to the SPA122's Ethernet port using a Ethernet network cable (this is necessary as the SPA122 will not allow you to access the web configuration interface without changing the default web password). Now connect your phone to the SPA122's Phone 1 port.

Can I configure the spa122 using the default static IP address?

Connecting the SPA122 directly to my PC did allow me to configure the device using the default static IP address. However, after attaching it to my network, the web GUI was still not accessible, even with Web admin access enabled. Also, the interactive voice response (IVR) does not allow changing of WAN access using code 7932.

How do I enable or disable remote upgrade on the spa122?

Click Enabled to enable remote upgrade, or click Disabled to disable remote upgrade. If enabled, remote upgrade permits firmware upgrade on the analog phone adapter from a device on the WAN side of the SPA122. You can only change this setting when you are connected to the SPA122 from the LAN.

How to configure SPA122?

What is web access management?

About this website

image

How do I access Cisco SPA122?

ProcedureUsing a LAN/Ethernet cable, connect the computer to the yellow Ethernet (LAN) port of the SPA122.Open Internet Explorer browser (IE is required to ensure the adapter's configuration page displays properly).Log in: admin / (administrator password)Click Voice > Provisioning.Click Submit.More items...•

What does a Cisco SPA122 do?

The Cisco SPA122 ATA with Router combines VoIP services with an internal router for LAN connectivity. Easy to install and use, it works over an IP network to connect analog phones and fax machines to a VoIP service provider and provides support for additional LAN connections.

How do I find the IP address of my Cisco SPA122?

At the voice prompt menu, enter 110 #. The phone will read back the IP address of the base, which can be entered into a browser to access the configuration. At the voice prompt menu, enter 210 #. The phone will read back the IP address of the base, which can be entered into a browser to access the configuration.

How do I factory reset my Cisco SPA122?

RESET — Press the Reset button to restart the SPA122 device. To restore it to factory default settings, hold the button for 20 seconds.

How do I access Cisco SPA112?

How to access the web configuration utility on the Cisco SPA112Open a web browser and enter the IP address of the phone adapter in the address bar, then press Enter.Enter the username of the device in the Username field. ... Enter the password of the device in the Password field.More items...

What does a Cisco ATA do?

Your analog telephone adapter (ATA) allows you to connect an analog device, such as an analog phone or fax machine, to your network. The connected device can then function like the IP phones in your network.

How do I log into my network configuration utility?

To open the web-based configuration utility: Open a Web browser. Enter the IP address of the WAP device that you are configuring in the address bar on the browser, and then press Enter. The Login page opens.

How do I log into ATA?

Enter this IP address into your browser 192.168. 15.1 to be prompted for login. Log in to the device using the default (case-sensitive) username ("admin") and password ("admin"), and then click Log In. Navigate to Administration tab.

How do I factory reset my SPA112?

To reset the device to the default factory configuration, there are two options:Dial **** and at the prompt dial 73738# and then press 1 to confirm.Locate the Reset Button on the back of the SPA112. ... Regardless of how you reset the device, it will take approximately 150 seconds to finish it's reset and reboot.

How do I reset my Cisco phone adapter?

Factory reset your Cisco SPA112 Hold the reset button down for 30s, or until the power LED light begins to flash again. Release the button. Allow the device to boot up; it may take 2-5 minutes for the reset process to complete. The power LED light will stop flashing once it has initialized.

How do I default a Cisco ATA?

Dial the following IVR code using the phone keypad: 73738 (RESET) followed by the # key. The IVR will ask you to confirm by pressing the 1 on the phone keypad. You must hang-up the phone to commence the reboot sequence.

What is phone Adaptor?

An analog telephone adaptor (ATA) is a device used to connect a standard telephone to a computer or network so that the user can make calls over the Internet.

How do I set up an ATA?

Step 1 Connect the network cable to your network and to the NETWORK port on the ATA. Step 2 Connect the phone cable to the PHONE 1 port on the ATA and to your analog device (phone or fax machine). If connecting a fax machine, connect it directly to the ATA.

Management

Use the Management pages to manage web access to the configuration utility and to enable protocols for remote configuration and network management.

Logging

The ATA allows you to record incoming, outgoing, and DHCP lists for various events that occur on your network.The Incoming Log displays a temporary list of the source IP addresses and destination port numbers for the incoming Internet traffic.

Factory Defaults

Use the Administration > Factory Defaults page to reset the ATA to the default configuration. Alternatively, press and hold the RESET button for 20 seconds. All user-changeable non-default settings will be lost. This may include network and service provider data.

Firmware Upgrade

Use the Administration > Firmware Upgrade page to upgrade the firmware on the ATA. It is not necessary to upgrade unless you are experiencing problems with the ATA or if the new firmware has a feature that you want to use. Before upgrading the firmware, download the firmware upgrade file for the ATA at: www.cisco.com/go/smallbizvoicegateways

Configuration Management

Use the Administration > Config Management pages to backup and restore the configuration settings for the ATA.

Reboot

Use the Administration > Reboot page to power cycle the ATA (if necessary) from the configuration utility. Alternatively, accomplish this task by pressing the RESET button.

How to enable web access management on a phone?

Step 1. Log in to the Phone Adapter Configuration Utility and choose Administration > Management > Web Access Management. The Web Access Management page opens: Step 2. Click the Enabled radio button to enable web access management to the administrator in the Admin Access field. This allows the administrator to access the interface remotely ...

What is the default port number for remote management?

This is the port number that will follow the address for remote management. The default is 80.

Why is web access management important?

Web access management is a very helpful feature for administrators because it gives the ability to access the configuration utility remotely via the internet. The objective of this article is to guide you on how to configure web access management on SPA.

How to configure SPA122?

Click the Any IP Address radio button to allow any remote IP address to configure the SPA122. Click the radio button directly below the Any IP Address radio button to only allow a single IP address or a range of addresses to remotely access the SPA122. Enter the IP address or range in the corresponding field.

What is web access management?

The Web Access Management page settings allow you to configure the ability to access the web configuration utility of a SPA122 remotely through the Internet. This configuration provides both the web and remote access utility for the user to have different options to access. Web access management controls the access available to permit web resources.

image
A B C D E F G H I J K L M N O P Q R S T U V W X Y Z 1 2 3 4 5 6 7 8 9