Remote-access Guide

configure remote access vpn cisco asa

by Mr. Ethan Turner Published 2 years ago Updated 2 years ago
image

There are eight basic steps in setting up remote access for users with the Cisco ASA.
  1. Configure an Identity Certificate.
  2. Upload the SSL VPN Client Image to the ASA.
  3. Enable AnyConnect VPN Access.
  4. Create a Group Policy.
  5. Configure Access List Bypass.
  6. Create a Connection Profile and Tunnel Group.
  7. Configure NAT Exemption.
Mar 19, 2009

How to connect to Cisco ASA?

  • You haven't installed the correct version of java
  • You did not allow connections and / or you did not set authentication and authorization using the local database (point 3)
  • You entered invalid credentials

How to setup a remote access VPN?

Use a VPN Router with the built-in VPN server capability

  • Launch a browser window from your PC connected to the routers’ network
  • Enter the router IP address in the search to login into your router
  • Enter the username and password of your router and login into it.
  • Go to the Settings page and select VPN Service or setup page.
  • Enable the VPN service by selecting the checkbox and apply

Can the Cisco ASA be used as a router?

The ASA is NOT a router, though and while you can do things on the ASA that can make it act something like a router it is important to understand the differences between true routing and what the ASA actually does.

How to check VPN tunnel status Cisco ASA?

  • show vpn-sessiondb l2l
  • show vpn-sessiondb ra-ikev1-ipsec
  • show vpn-sessiondb summary
  • show vpn-sessiondb license-summary
  • and try other forms of the connection with "show vpn-sessiondb ?"

image

How configure Cisco ASA site to site VPN?

1:0814:10Cisco ASA Site-to-Site VPN Configuration (Command Line)YouTubeStart of suggested clipEnd of suggested clipFirst of all we need to go into configuration mode so config T and now we're going to enable ISOMoreFirst of all we need to go into configuration mode so config T and now we're going to enable ISO camp on the outside interface that ISO camp is the handshake part of the configuration.

How configure AnyConnect Cisco ASA?

5 Steps to Configure Cisco AnyConnect VPNConfigure AAA authentication. The first thing to configure is AAA authentication. ... Define VPN protocols. When users connect their VPN, they'll need an IP address for the VPN session. ... Configure tunnel groups. ... Set group policies. ... Apply the configuration. ... Authenticating logic flow.

What is Cisco remote access VPN?

This allows remote users to connect to the ASA and access the remote network through an IPsec encrypted tunnel. The remote user requires the Cisco VPN client software on his/her computer, once the connection is established the user will receive a private IP address from the ASA and has access to the network.

How does Cisco AnyConnect VPN Work?

Remote and mobile users use the Cisco AnyConnect Secure VPN client to establish VPN sessions with the adaptive security appliance. The adaptive security appliance sends web traffic to the Web Security appliance along with information identifying the user by IP address and user name.

How do I configure AnyConnect on ASA 5505?

Quick guide: AnyConnect Client VPN on Cisco ASA 5505Click on Configuration at the top and then select Remote Access VPN.Click on Certificate Management and then click on Identity Certificates.Click Add and then Add a new identity certificate.Click New and enter a name for your new key pair (ex: VPN)More items...•

How do I add VPN details to Cisco AnyConnect?

InstallUninstall any previous versions of Cisco AnyConnect.Install Cisco AnyConnect app from the Apple App Store or Google Play Store.Open the Cisco AnyConnect app.Select Add VPN Connection.Enter a Description, for example, CMU VPN and the Server Address vpn.cmu.edu.If prompted, allow the changes.Click Save.

How do I setup remote access to VPN?

Configure Remote Access as a VPN ServerOn the VPN server, in Server Manager, select the Notifications flag.In the Tasks menu, select Open the Getting Started Wizard. ... Select Deploy VPN only. ... Right-click the VPN server, then select Configure and Enable Routing and Remote Access.More items...•

How does remote access VPN Work?

A remote access VPN works by creating a virtual tunnel between an employee's device and the company's network. This tunnel goes through the public internet but the data sent back and forth through it is protected by encryption and security protocols to help keep it private and secure.

What VPN types are supported by ASA?

For VPN Services, the ASA 5500 Series provides a complete remote-access VPN solution that supports numerous connectivity options, including Cisco VPN Client for IP Security (IPSec), Cisco Clientless SSL VPN, network-aware site-to-site VPN connectivity, and Cisco AnyConnect VPN client.

What type of VPN is Cisco AnyConnect?

Cisco AnyConnect VPNs utilize TLS to authenticate and configure routing, then DTLS to efficiently encrypt and transport the tunneled VPN traffic, and can fall back to TLS-based transport where firewalls block UDP-based traffic.

Is Cisco AnyConnect a VPN?

Cisco AnyConnect Client helps us to make secure , safe and reliable VPN connection to our organization's private network with multiple security services to safe and protect company's data. It gives freedom to employees to get connected from anywhere anytime, thus making life easier for remote workers.

Is Cisco AnyConnect SSL or IPSec?

Anyconnect is the replacement for the old Cisco VPN client and supports SSL and IKEv2 IPsec. When it comes to SSL, the ASA offers two SSL VPN modes: Clientless WebVPN.

Where is the Cisco AnyConnect client image found on the Cisco ASA?

Where is the Cisco AnyConnect client image found on the Cisco ASA? Flash. The Cisco AnyConnect client image is located in flash. Otherwise, it must be uploaded from the local machine.

How do I download Cisco AnyConnect from Asa?

Just load a new image to the ASA (under Configuration -> Remote-Access VPN -> Network (Client) Access -> AnyConnect Client Software) and the client will load the new software the next time when the client connects. Of course the client shouldn't have a setting applied to not download new software.

How do I get Cisco AnyConnect secure mobility client?

Open a web browser and navigate to the Cisco Software Downloads webpage.In the search bar, start typing 'Anyconnect' and the options will appear. ... Download the Cisco AnyConnect VPN Client. ... Double-click the installer.Click Continue.Go over the Supplemental End User License Agreement and then click Continue.More items...

What is one benefit of using ASDM to configure a Cisco ASA?

ASDM provides increased configuration security. It hides the complexity of security commands. It does not require any initial device configuration. It does not require a remote connection to a Cisco device.

Which crypto protocol allows the IPsec client and the ASA to establish a shared secret key?

Specify the Diffie-Hellman group for the IKE policy—the crypto protocol that allows the IPsec client and the ASA to establish a shared secret key.

How many interfaces does an ASA have?

An ASA has at least two interfaces, referred to here as outside and inside. Typically, the outside interface is connected to the public Internet, while the inside interface is connected to a private network and is protected from public access.

What is the default LAN to LAN tunnel group?

There are two default tunnel groups in the ASA system: DefaultRAGroup, which is the default remote-access tunnel group, and DefaultL2Lgroup, which is the default LAN-to-LAN tunnel group. You can change these groups, but do not delete them. The ASA uses these groups to configure default tunnel parameters for remote access and LAN-to-LAN tunnel groups when there is no specific tunnel group identified during tunnel negotiation.

What files can Cisco AnyConnect have?

Virtual File System creation for each context can have Cisco Anyconnect files like Image and profile.

What is the first phase of ISAKMP?

Phase 1 creates the first tunnel to protect later ISAKMP negotiation messages. Phase 2 creates the tunnel that protects data travelling across the secure connection.

Is Mobike available on ASA?

Mobike is available by default on ASAs since version 9.8 (1), meaning Mobike is “always on.” Mobike is enabled for each SA only when the client proposes it and the ASA accepts it. This negotiation occurs as part of the IKE_AUTH exchange.

Do you need a mask for a VPN?

The address mask is optional. However, You must supply the mask value when the IP addresses assigned to VPN clients belong to a non-standard network and the data could be routed incorrectly if you use the default mask. A typical example is when the IP local pool contains 10.10.10.0/255.255.255.0 addresses, since this is a Class A network by default. This could cause routing issues when the VPN client needs to access different subnets within the 10 network over different interfaces.

How many interfaces does an ASA have?

The ASA has two interfaces: inside and outside. Imagine the outside interface is connected to the Internet where a remote user wants to connect to the ASA. On the inside we find R1, I will only use this router so the remote user has something to connect to on the inside network. Let’s look at the configuration!

What is VPN_POLICY?

The group policy is called VPN_POLICY and it’s an internal group policy which means it is created locally on the ASA. You can also specify an external group policy on a RADIUS server. I added some attributes, for example a DNS server and an idle timeout (15 minutes). Split tunneling is optional but I added it to show you how to use it, it refers to the access-list we created earlier.

Does Cisco VPN require ASA?

The remote user requires the Cisco VP N client software on his/her computer, once the connection is established the user will receive a private IP address from the ASA and has access to the network .

Can remote VPN users access certain networks?

If you want to configure an access-list so the remote VPN users can only reach certain networks , IP addresses or ports then you can apply this under the group policy.

Can you use VPN on remote network?

If you don’t want this then you can enable split tunneling. With split tunneling enabled, we will use the VPN only for access to the remote network. Here’s how to enable it:

How many interfaces does an ASA have?

An ASA has at least two interfaces, referred to here as outside and inside. Typically, the outside interface is connected to the public Internet, while the inside interface is connected to a private network and is protected from public access.

What is the first phase of ISAKMP?

Phase 1 creates the first tunnel to protect later ISAKMP negotiation messages. Phase 2 creates the tunnel that protects data travelling across the secure connection.

What is the default LAN to LAN tunnel group?

There are two default tunnel groups in the ASA system: DefaultRAGroup, which is the default remote-access tunnel group, and DefaultL2Lgroup, which is the default LAN-to-LAN tunnel group. You can change them but not delete them. The ASA uses these groups to configure default tunnel parameters for remote access and LAN-to-LAN tunnel groups when there is no specific tunnel group identified during tunnel negotiation.

Is IPv6 supported for SSL?

Assigning an IPv6 address to the client is supported for the SSL protocol. This feature is not supported for the IKEv2/IPsec protocol.

Do you need a mask for a VPN?

The address mask is optional. However, You must supply the mask value when the IP addresses assigned to VPN clients belong to a non-standard network and the data could be routed incorrectly if you use the default mask. A typical example is when the IP local pool contains 10.10.10.0/255.255.255.0 addresses, since this is a Class A network by default. This could cause routing issues when the VPN client needs to access different subnets within the 10 network over different interfaces.

Can ASA assign IPv4 and IPv6?

You can configure the ASA to assign an IPv4 address, an IPv6 address, or both an IPv4 and an IPv6 address to an AnyConnect client by creating internal pools of addresses on the ASA or by assigning a dedicated address to a local user on the ASA.

When remote users connect to our WebVPN, do they have to use HTTPS?

The following option is not required but useful, whenever someone accesses the ASA through HTTP then they will be redirected to HTTPS:

What is AnyConnect VPN?

Anyconnect is the replacement for the old Cisco VPN client and supports SSL and IKEv2 IPsec. When it comes to SSL, the ASA offers two SSL VPN modes: Clientless WebVPN. AnyConnect VPN. The clientless WebVPN method does not require a VPN client to be installed on the user’s computer. You just open your web browser, ...

What happens when a VPN user terminates a session?

Normally when the remote VPN user terminates the session, the anyconnect installer will be uninstalled. The anyconnect keep-installer installed command leaves it installed on the user’s computer.

What happens when you have an inbound access list?

When you have an inbound access-list on the outside interface then all your decrypted traffic from the SSL WebVPN has to match the inbound access-list. You can either create some permit statements for the decrypted traffic or you can just tell the ASA to let this traffic bypass the access-list:

Why does my client tries to download AnyConnect?

The client tries to download the Anyconnect automatically, this is because of the anyconnect ask none default anyconnect command that we used. Since we are using a self-signed certificate you will get the following error message:

What is the IP address of AnyConnect?

You can see that we received IP address 192.168.10.100 (the first IP address from the VPN pool). Anyconnect creates an additional interface, just like the legacy Cisco VPN client does.

What is an ayconnECT_policy?

The group policy is called “ANYCONNECT_POLICY” and it’s an internal group policy which means that we configure it locally on the ASA. An external group policy could be on a RADIUS server.

Information About Remote Access IPsec VPNs

Remote access VPNs allow users to connect to a central site through a secure connection over a TCP/IP network such as the Internet. The Internet Security Association and Key Management Protocol, also called IKE, is the negotiation protocol that lets the IPsec client on the remote PC and the ASA agree on how to build an IPsec Security Association.

Licensing Requirements for Remote Access IPsec VPNs

The following table shows the licensing requirements for this feature:

Guidelines and Limitations

This section includes the guidelines and limitations for this feature.

Configuring Remote Access IPsec VPNs

This section describes how to configure remote access VPNs and includes the following topics:

image
A B C D E F G H I J K L M N O P Q R S T U V W X Y Z 1 2 3 4 5 6 7 8 9