What is a DD-WRT WAP?
With DD-WRT you can buy a device marketed as a router and use it as a WAP. [edit]Secondary Router on a Separate Subnet This is simply a gateway router that is downstream of a primary gateway router.
Do I need DD-WRT If I have an Ethernet cable?
Linking routers by Ethernet cables does not require DD-WRT on any router. However, some more advanced settings are available in DD-WRT. As an example, some colleges still allow students to have their own WAP.
How to disable DHCP on a secondary access point router?
On the secondary access point router: Do a hard reset Disable DHCP and set the wireless channel different from the other router(s) Set the IP address to 192.168.1.2 (or any IP outside the gateway DHCP range that does not collide with the gateway nor any other static devices)
What is wireless access point (WAP)?
[edit]Introduction For a large network where the DD-WRT router does not provide suitable network core, Wireless Access Point(WAP or just 'AP') allows wireless clients to be a part of the larger network.
See more
How do I access my DD-WRT remotely?
Go to Administration -> Management -> Remote Access. Enable the necessary settings for remote Web or SSH access (note the WAN IP and port number), then in your main router forward that port to the WAN IP address of the Repeater.
What is the DD-WRT default password?
adminThe default username is root and the default password is admin (from v23 SP1).
How do I find my DD-WRT password?
Both routers have a password of "admin" by default. Click on "support and documentation" in your router's manufacturer's website to find out their default password.
How do I reset DD-WRT to default settings?
Turn the device on, and then hold the Factory Reset button for 30 seconds. After you release, it should be reset to the default username and password.
How do I access my WRT router?
Type "192.168. 1.1" into your Web browser's address bar and press "Enter" to access the Web-based interface. Log in with the user name "root" and the password "admin" to continue. You can use the Web interface to configure your DD-WRT router's settings, including setting a custom user name and/or password.
What does DD-WRT stand for?
DresDren-Wireless RouTerWhat Does DD-WRT Mean? DD-WRT (DresDren-Wireless RouTer) is a type of firmware for routers based on the Linux kernel. It was designed especially for 802.11a/b/g/h/n routers having the Broadcom or Atheros chipsets.
How do I change my DD-WRT router username and password?
1:023:13How to change DD-WRT Router Username & Password - YouTubeYouTubeStart of suggested clipEnd of suggested clipType in the IP of the root. If you've had it from us it's going to be 192.168. 1.1 and click enter.MoreType in the IP of the root. If you've had it from us it's going to be 192.168. 1.1 and click enter.
How do I change my DD-WRT WIFI password?
How do I change the wireless password in my DD-WRT Cloakbox VPN Router?Click on Wireless Tab.Click on the Wireless Security sub-tab.Change the WPA2/Personal Key to the value you like. ... Click Save.Restart the CloakBox.
How do I setup my DD-WRT router as a repeater?
Go to the wireless tab.Choose Repeater Bridge under wireless mode.Match your SSID and channel settings exactly to the main router you will be connecting to.Make sure bridged is selected.Click Save.
Do not 30 30 30 reset ARM routers?
How to Perform a 30-30-30 Router ResetWith the router plugged in and powered on, depress the reset button for 30 seconds. ... While still holding down the button, unplug the router from its power source for another 30 seconds.With the reset button still held down, turn the power back on and hold for another 30 seconds.
How do you fix a bricked router?
If your router is bricked, unplug it for 30 seconds and plug it back in. If that didn't work, attempt a hard manual reset by pressing a straightened paper clip onto the reset button located on the outside of the router.
What does flash your router mean?
Flashing a router is the process of replacing the software that makes it work with another software block. The software that makes it work is called the firmware. Usually, the replacement firmware is an upgrade with better all-round compatibility, functionality, and performance.
What is the default password for Netgear?
passwordWhen you set up a new NETGEAR router for the first time, it is configured with factory default settings, including login credentials. By default, the www.routerlogin.net user name is admin and the password is password.
Why DD-WRT is better?
Essentially, it echoes the signal to widen its range. With DD-WRT, you can take a regular router and make it into a range extender. A stronger, better, optimized DD-WRT signal may also be able to more easily reach farther devices, even without a range extender.
How do you reset your router to factory settings?
How to reset your router to restore factory default settingsLocate the Reset button on the back of your router.With the router powered on, use the pointed end of a paperclip or similar object to press and hold the Reset button for 15 seconds.Wait for the router to fully reset and power back on.
How to connect a WAP to a LAN?
You can either Uplink through one of the router's LAN ports, or use the WAN port that is normally connected to the cable/DSL modem.
What is a WAP router?
For a large network where the DD-WRT router does not provide suitable network core, Wireless Access Point(WAP or just 'AP') allows wireless clients to be a part of the larger network. In this case, clients normally get DHCP configuration from the gateway or some other DHCP server, and could be accessed by other clients on the network (if allowed).
What to do if your router is not working?
If not working, reboot the router to be sure all settings have been applied.
What happens if you don't turn off DHCP?
If you did not turn off DHCP, when you plug your router into the network (after configuration), your WAP may provide IP addresses to clients on the wired network, and this may be inappropriate.
How to set up a secondary router?
If you want a secondary router to be on a separate subnet from the primary, just hard reset the router and set the router's IP to, e.g., 192.168.5.1 on the basic setup page. Then set security and SSID on the Wireless tab, hit Save then Apply, and finally plug the LAN cable from your primary to the WAN of the second router.
How to allow clients to roam freely?
If you are installing additional Access Points to cover a broader area with Wi-Fi access, it is possible to allow clients to roam freely between them. The common method is to use the same SSID and Security settingson each access point. The clients control when to switch in between APs. Most clients will switch when they see a more powerful AP available but some client radios are not able to listen for a new AP when connected to an existing AP and as a result those clients will not roam to the new AP until they completely lose signal from the old one. A typical roaming transition from one AP to the other takes about 50ms if using simple authentication (open or WPA2 PSK AES)
Does DD-WRT support 802.11?
Because of that, the IEEE 802.11r-2008 protocol, a.k.a. Fast Transition (FT), was developed. DD-WRT does not currently support 802.11r FT but there is support for it in OpenWRT. The wireless client must also support Fast Roaming for this protocol for it to work; typically it will be cell phones that support it.