How do I access the DD-WRT Web-GUI?
See Telnet/SSH_and_the_Command_Line for more details. After installing DD-WRT Firmware you can access the DD-WRT Web-GUI using a web browser pointing to the same IP address as before you installed DD-WRT.
How to enable remote web management of DD-WRT via telnet?
Since, it was not enabled I found the following set of commands in the documentation to enable remote web management of DD-WRT via Telnet. You first have to telnet to your remote router by simply typing telnet 124.xxx.xxx.xx (remote IP).
Do I need to set my own password for DD-WRT?
The latest versions of DD-WRT will require you to set your own username and password when you first access the web interface. Because the SSH user is always root, it is critical that a strong password be used.
How do I access my DD-WRT remotely?
Go to Administration -> Management -> Remote Access. Enable the necessary settings for remote Web or SSH access (note the WAN IP and port number), then in your main router forward that port to the WAN IP address of the Repeater.
How do I access DD-WRT interface?
Type "192.168. 1.1" into your Web browser's address bar and press "Enter" to access the Web-based interface. Log in with the user name "root" and the password "admin" to continue. You can use the Web interface to configure your DD-WRT router's settings, including setting a custom user name and/or password.
Which is better open WRT or DD-WRT?
When it comes down to it, OpenWrt is the way to go. DD-WRT is a close, close second. It's proven to be a solid choice for custom router firmware, but it lacks in some features, customization, and update availability.
What is the DD-WRT default password?
adminThe default username is root and the default password is admin (from v23 SP1).
How do I access DD-WRT Repeater Bridge?
Go to the wireless tab.Choose Repeater Bridge under wireless mode.Match your SSID and channel settings exactly to the main router you will be connecting to.Make sure bridged is selected.Click Save.
How do I find my DD-WRT password?
Both routers have a password of "admin" by default. Click on "support and documentation" in your router's manufacturer's website to find out their default password.
Can I install OpenWrt from DD-WRT?
Check the DD-WRT site to find the most current, stable firmware version compatible with your router hardware in preparation for the install. Access the OpenWRT router command console through SSH to install DD-WRT, and perform the DD-WRT installation via command line, which requires fewer steps and less complexity.
Is OpenWrt faster?
OpenWrt reduces latency/lag and increased network throughput via bufferbloat control algorithms. Wi-Fi improvements support higher data rates and airtime fairness between stations.
Is DD-WRT faster?
Faster connection speeds. Many of the above benefits combine to offer accelerated internet connection speeds with DD-WRT.
What does DD-WRT stand for?
DresDren-Wireless RouTerWhat Does DD-WRT Mean? DD-WRT (DresDren-Wireless RouTer) is a type of firmware for routers based on the Linux kernel. It was designed especially for 802.11a/b/g/h/n routers having the Broadcom or Atheros chipsets.
How do you find the IP address of a router?
Find Your Router IP Address on AndroidGo to Settings.Tap Wi-Fi Settings.Tap and hold on your connected network and select Manage Network Settings.Check the box next to Show Advanced Options.Select Static under IP Settings.Your router IP address is listed under the Gateway section.
How do I change my DD-WRT router username and password?
1:023:13How to change DD-WRT Router Username & Password - YouTubeYouTubeStart of suggested clipEnd of suggested clipType in the IP of the root. If you've had it from us it's going to be 192.168. 1.1 and click enter.MoreType in the IP of the root. If you've had it from us it's going to be 192.168. 1.1 and click enter.
How do I reset DD-WRT to default settings?
Turn the device on, and then hold the Factory Reset button for 30 seconds. After you release, it should be reset to the default username and password.
What is the default password for Netgear?
passwordWhen you set up a new NETGEAR router for the first time, it is configured with factory default settings, including login credentials. By default, the www.routerlogin.net user name is admin and the password is password.
How do you reset your router to factory settings?
How to reset your router to restore factory default settingsLocate the Reset button on the back of your router.With the router powered on, use the pointed end of a paperclip or similar object to press and hold the Reset button for 15 seconds.Wait for the router to fully reset and power back on.
How to telnet to a remote router?
You first have to telnet to your remote router by simply typing telnet 124.xxx.xxx.xx (remote IP). Input your username (usually root) and password (which you had kept when you first configured the router). After you are through with Telnet, you can now run commands since you are a root user.
How long to wait to access router remotely?
Run the following set of commands one by one in the console. Just wait for 3-5 minutes, while your router reboots and then you can easily access your router remotely via the web browser. However, you should suffix your router’s address with the port no. 8080 as specified in the above command.
What happens if you lose web access to your router?
If for some reason you completely lost web access to the router, the web server (HTTP daemon) may be shut down. To regain access try starting the web server. SSH or telnet into the router and enter the following commands:
Can you restart HTTP daemon?
You can try restarting the HTTP daemon since you can still SSH in. If that doesn't work, you may have to resort to a full reset/reboot.
primexx
Hi, i just noticed that I can access/login my router's web admin interface by visiting my external IP address from outside my network. i thought i shouldn't be able to do this?
primexx
doesn't work either, that governs remote access (web gui managemnt, ssh, telnet).
eangulus
Disabling Remote HTTP access shouldn't stop internal IP addres's. It should only stop access from the WAN port.
primexx
Disabling Remote HTTP access shouldn't stop internal IP addres's. It should only stop access from the WAN port.
eangulus
Are you sure your accessing it externally? Like your not on a VPN or not still connected to the wireless or something of those lines. I know its a stupid question but I have made some silly mistakes before too.
primexx
yea i've been trying from a web proxy and also my neighbour's open wifi, can access it in both. i don't have vpn.
primexx
ok turns out the firewall rules were all messed up somehow. it's good now.
Username and Password
- The latest versions of DD-WRT will require you to set your own username and password when you first access the web interface. Because the SSH user is always root, it is critical that a strong password be used. These passwords should be a minimum of 12 characters and use numbers a…
Elements of The Web-Gui
- The Web-GUI has five main elements 1. 1.The tabbed menu system 2. 2.Main area 3. 3.Action buttons 4. 4.Help information 5. 5.Some system essentials Clicking these text buttons gives you access to furter information 1. 1.More... (More Help) 2. 2.Firmware details Some notes about the screen elements. 1. The default information screen is the same as menu selection: Status->Sys-I…
Menu Interface Map
- Select one of the menu points below for information about settings within that menu page. (Menu structure as of June 2012 - svn19342 Mega). 1. Setup 1.1. Basic Setup 1.2. DDNS 1.3. MAC Address Clone 1.4. Advanced Routing 1.5. VLANs 1.6. Networking 1.7. EoIP Tunnel 2. Wireless 2.1. Basic Settings 2.2. Radius 2.3. Wireless Security 2.4. MAC Filter 2.5. Advanced Settings 2.6. …
Setting Details About The Web-Gui
- Under Administration -> Managementyou can set various details about the Web-GUI. Like: 1. set Username and Password 2. control Access to the Web-GUI locally/remotely and more 3. select between different Router GUI styles [[Image:
Regaining Access
- [edit] Locally
If for some reason you completely lost web access to the router, the web server (HTTP daemon) may be shut down. To regain access try starting the web server. SSH or telnetinto the router and enter the following commands: To connect through secure HTTP, add the option -Sat the end of … - [edit] Remotely
Method 1: See Enable Web Interface Over SSH? Method 2: If you're at a remote location and have access to your router through SSH or telnet, but you'd like to enable remote web access, you may use the following command to allow access from one remote IP address: 1. 1.1. iptables -I INPU…
Simulation
- (This section has not been updated for quite some time). A setup simulation of V22-DD-WRT interface is here. A setup simulation of V23-DD-WRT interface is here. A setup simulation of V24beta-DD-WRT interface is here.