For DrayTek Routers, enable the VPN service via [VPN and Remote Access] > [Remote Access Control Setup] page will open the required ports automatically. And please also make sure that the required ports are not redirected or opened for the LAN clients.
Full Answer
How do I configure a DrayTek router for remote management?
A quick setup guide for remote management is located here: Configuring a DrayTek router for remote management Tick Allow management from the Internet to enable management over the internet on the interfaces selected. i.e. ticking HTTPS Server enables access to the router's HTTPS interface when accessing the router from the internet.
Why is my DrayTek router not connecting to the Internet?
If the address shown starts with 10.x.x.x, 172.16.x.x or 192.168.x.x, or if the router is known to be behind another NAT router, the DrayTek router may still be inaccessible from the internet. This can usually be resolved by forwarding the DrayTek router's management ports on the router that the DrayTek is receiving its WAN connection through.
How do I remotely access the management interfaces on my router?
Once the router is online, the management interfaces enabled under the Internet Access Controlsection can be accessed remotely by accessing the router's WAN IP(s). The router's WAN IP can be checked from the [Online Status] > [Physical Connection]page, this will show the IP address under each of the WAN Statusheadings:
How do I enable access control from the Internet?
Allow access from the Internet Go to System Maintenance >> Access Control. At Internet Access Control, select “Enable” for the management interface you'd like to access from the Internet. (SSH for CLI, HTTPS access for the Web UI).
How do I set up DrayTek remote?
Go to System Maintenance >> Access Control. At Internet Access Control, select “Enable” for the management interface you'd like to access from the Internet. (SSH for CLI, HTTPS access for the Web UI).
How do I set up DrayTek access point?
Wireless Setup Go to [Wireless LAN 2.4GHz] > [General Setup], enable Wireless LAN and set the SSID. If you have other existing Access Points on the network, you can set the same SSID details so that your client devices will see just the one wireless network. Click OK when you are done to save and apply the changes.
How do I connect to DrayTek VPN?
Confirm User Name and Password, and click OK to start the SSL VPN connection to Vigor Router....SSL VPN Setup on WindowsEnter Profile Name.Select "SSL VPN Tunnel" in Type.Enter Vigor Router's WAN IP in IP or Hostname.Enter User Name and Password.Enable Fast SSL.Click OK.
How do I connect my DrayTek router?
0:113:23Tutorial - How to log into your DrayTek Vigor Router - YouTubeYouTubeStart of suggested clipEnd of suggested clipMake sure that the router is powered and switched. On then plug the ethernet cable. Into the LANMoreMake sure that the router is powered and switched. On then plug the ethernet cable. Into the LAN port. Then plug the other end into the ethernet port on your device.
How do you set up a universal repeater?
F9-how to setup Universal RepeaterOpen ”Internet Settings”, Select “Universal Repeater”, and then select the signal source that needs to be amplified.Enter the password for the wireless signal that needs to be extended , click "connect", and then the router will restart.More items...•
What is DrayTek Smart VPN client?
The DrayTek Smart VPN Client for Microsoft Windows provides SSL VPN Tunnnel support and additionally supports PPTP, L2TP, IPsec, L2TP over IPsec with profiles for each VPN Tunnel. It supports Windows 7, Windows 8. x, Windows 10 and Windows XP. Available in the Router Tools section of the DrayTek UK Downloads page.
How does SSL VPN Work?
An SSL tunnel VPN allows a web browser to securely access multiple network services that are not just web-based via a tunnel that is under SSL. These services could be proprietary networks or software built for corporate use only that cannot be accessed directly via the internet.
How do you use mOTP?
On the router, go to User Management>>User profile, and click add.Choose the interface you want to apply to.Enable Two-FA via mOTP.Enable Use mOTP, then enter the PIN code and the same Secret as Step 1.Click Apply.
What is the IP address for DrayTek router?
192.168.1.1Usually, you can access the router's management page at 192.168. 1.1, which is the router's default LAN IP address.
How do I change the IP address on my DrayTek router?
On LAN >> General Setup >> LAN 1 Details page, you can change the IP settings. Network Administrators may use any IP subnet that is preferred, as long as it does not conflict with the WAN IP settings. By default, Vigor Router uses the subnet 192.168. 1.0/255.255.
How do I log into DrayTek vigor?
How to login my Vigor RouterConnect a computer to one of the router's LAN ports by an Ethernet cable.Make sure the network interface is using an IP in the 192.168. ... Open a browser on the computer. ... After logging in, you will access the management page of the router.
How do I reset my DrayTek router?
Go to System Maintenance >> Reboot System on the web page. The following screen will appear. Choose Using factory default configuration and click OK. After few seconds, the router will reboot with all settings back to to the factory default.
What is my DrayTek username?
Logging onto a Draytek router You will then be directed to the web interface for the device and you will need to log in. The default Username for the device is 'admin' and the default password will be the same (see below).
How do I change my DrayTek WIFI password?
Go to [System Maintenance] > [Admin Setting]. Enter the existing password in the Old Password box, then put the new password in both the New Password and Confirm Password boxes. Click OK to apply the change. The router will then display this message to indicate that the password has changed.
How do I access DrayTek vigor 130?
With that connected, the Vigor 130 modem's web interface can be accessed on http://192.168.2.1 with a username of "admin" and a password of "admin" by default. In the modem's web interface, go to [Internet Access] > [General Setup], on that page, the VLAN Tag insertion (VDSL2) setting will be enabled and set to 101.
How to restrict remote access to a specific IP?
To restrict the remote access to a specific IP only, enable Access List then add the public IP of the remote host into the IP List. (The option should be disabled if the remote access peer doesn't have a static public IP. )
How to enable WAN access on router?
Make sure the WAN Interface is online, and the router has a public IP address. 2. Allow access from the Internet. Go to System Maintenance >> Access Control. At Internet Access Control, select “Enable” for the management interface you'd like to access from the Internet.
How to access the web management page on a router?
With the configuration above, you may access the router's web management page from the Internet by https:// [The Router's WAN IP].
Why is Vigor router disabled?
Vigor Router offers remote management access; however, it is disabled for security reason. If you would like to manage the router from the Internet, follow the steps below.
How to see the login page of a router?
Open a browser, input https:// [the router's WAN IP] in the address bar, and hit Enter. You should see the login page of the router's Web-based UI. (NOTE: If you changed the router's HTTPS port, specify the port number after the IP address.)
