How do I enable the routing and remote access service?
To Enable the Routing and Remote Access Service Click Start, point to Administrative Tools, and then click Routing and Remote Access. In the left pane of the console, click the server that matches the local server name. If the icon has a red arrow in the lower-right corner, the Routing and Remote Access service isn't enabled. Go to step 3.
How do I install the remote access role?
You must install the Remote Access role on a server in your organization that will act as the Remote Access server. On the server that will act as the Remote Access server, in the Server Manager console, in the Dashboard, click Add roles and features. Click Next three times to get to the server role selection screen.
How do I access my Remote Desktop settings?
To access your Remote Desktop settings, click on the Server Manager icon in the lower-left corner of your desktop next to your Start button. On the right side of your Server Manager window, you will see a link to Configure Remote Desktop under Computer Information. Click on this link to view your Remote Desktop settings.
Should I use rip or dynamic routing for Windows Server 2008?
On the other hand, on a network where you want the Windows Server 2008 system to route for 25 networks or to exchange routes with a Cisco network that uses RIP, you will want to choose dynamic routing. Obviously, you do not want to have to key in those 25 networks manually nor can you provide the true dynamic features that RIP provides.
How do I set up Remote Access and Routing?
Click Start, point to Administrative Tools, and then click Routing and Remote Access. In the console tree, expand Routing and Remote Access, expand the server name, and then click Remote Access Policies. Right-click the right pane, point to New, and then click Remote Access Policy.
What does Routing and Remote Access do?
Routing and Remote Access Service (RRAS) is a Microsoft API and server software that makes it possible to create applications to administer the routing and remote access service capabilities of the operating system, to function as a network router.
What is RRAS LAN Routing?
RRAS provides multiprotocol LAN-to-LAN, LAN-to-WAN, virtual private network (VPN), and network address translation (NAT) routing services. RRAS is intended for use by system administrators who are already familiar with routing protocols and services.
How do I set up RRAS?
Right-click the VPN server, then select Configure and Enable Routing and Remote Access. The Routing and Remote Access Server Setup Wizard opens. In the Welcome to the Routing and Remote Access Server Setup Wizard, select Next. In Configuration, select Custom Configuration, and then select Next.
Where can I find Remote Access and routing?
4:257:49Install and Configure RRAS (Routing and Remote Access Service)YouTubeStart of suggested clipEnd of suggested clipAnd i'm gonna close the configure remote access window as well. And then i will just use the toolsMoreAnd i'm gonna close the configure remote access window as well. And then i will just use the tools under routing and remote access. And i'm gonna use the option called configure and enable routing and
What is the main purpose of a RAS server?
A remote access server (RAS) is a type of server that provides a suite of services to remotely connected users over a network or the Internet. It operates as a remote gateway or central server that connects remote users with an organization's internal local area network (LAN).
What is the difference between RAS and RRAS?
Microsoft Remote Access Server (RAS) is the predecessor to Microsoft Routing and Remote Access Server (RRAS). RRAS is a Microsoft Windows Server feature that allows Microsoft Windows clients to remotely access a Microsoft Windows network.
What is the full form of RRAS?
Routing and Remote Access Service (RRAS)
How do I remotely access another computer from intranet?
Setting up remote access is only necessary when attempting to use Remote Desktop Connection from outside of your LAN. In order to connect remotely, port 3389 must be open on your router. The host computer must be turned on, and have Remote Desktop enabled.
Is IIS required for RRAS?
RRAS: Features are managed in the Routing and Remote Access console. The Remote Access server role is dependent on the following features: - Web Server (IIS): Required to configure the network location server and default web probe.
How do I enable NAT in RRAS?
After the RRAS service has been restarted, expand IPv4, right-click General, and then click New Routing Protocol. In Routing protocols, click NAT, and then click OK. Right-click NAT, and then click New Interface. Select the interface that connects to your private intranet, and then click OK.
How can you install enable and configure Remote Access services on server?
Install the Remote Access roleOn the DirectAccess server, in the Server Manager console, in the Dashboard, click Add roles and features.Click Next three times to get to the server role selection screen.On the Select Server Roles dialog, select Remote Access, and then click Next.Click Next three times.More items...•
What is remote access control?
Remote access control refers to the ability to monitor and control access to a computer or network (such as a home computer or office network computer) anywhere and anytime. Employees can leverage this ability to work remotely away from the office while retaining access to a distant computer or network.
How can you install enable and configure remote access services on server?
Install the Remote Access roleOn the DirectAccess server, in the Server Manager console, in the Dashboard, click Add roles and features.Click Next three times to get to the server role selection screen.On the Select Server Roles dialog, select Remote Access, and then click Next.Click Next three times.More items...•
What was important in the route add command?
What was important in the route add command was the network we want to add, its subnet, the destination/gateway, and the interface for that route.
How many networks can you use RIP on Windows Server 2008?
On the other hand, on a network where you want the Windows Server 2008 system to route for 25 networks or to exchange routes with a Cisco network that uses RIP, you will want to choose dynamic routing. Obviously, you do not want to have to key in those 25 networks manually nor can you provide the true dynamic features that RIP provides.
How to configure RIPv2?
To do this, go to the RIP section, right click, click on New Interface, select the interface you want to add under RIP as you see in Figure 9.
What is static routing?
With static routing, you must make an entry on your Windows Server for every network that will be routed by that server. Thus, for a simple network with a single windows server, routing traffic between two networks, static routing is a “no brainer”. You could configure it with two simple route add commands.
What are the interface numbers in Windows Server?
Windows Server IP interfaces are labeled with an interface number. The interface numbers in Figure 1 are 16, 14, 1, 15, 20, and 12. These interface numbers are used whenever you add or delete routes to the routing table.
What is the second important thing in the route print output?
The second important thing in the route print output is the IPv4 Routing Table. This shows us the network destination, network mask, the default gateway, interface, and metric. This table tells the Windows Server where to route the traffic.
Does Windows Server 2008 have static routing?
Windows Server 2008 has one solid static routing option and one scalable dynamic routing option – RIP V2. I discussed how OSPF has been removed from Windows 2008 (and how I feel about that). We talked about why you would use static routing versus dynamic routing. Finally, I showed you how to configure static routing with the route command and dynamic routing by installing RIPV2 in Windows 2008 Routing and Remote Access.
Question
I am having an issue mapping drives over my VPN connection using the MS Routing and Remote access connection.
Answers
I'm not sure why this has come up recently in multiple threads in the past week. Nonetheless, it's more than likely a configuration issue when it was setup, such as leaving that filter checkbox checked running the config wizard.
All replies
I'm not sure why this has come up recently in multiple threads in the past week. Nonetheless, it's more than likely a configuration issue when it was setup, such as leaving that filter checkbox checked running the config wizard.
What do I get with a subscription?
With your subscription - you'll gain access to our exclusive IT community of thousands of IT pros. You'll also be able to connect with highly specified Experts to get personalized solutions to your troubleshooting & research questions. It’s like crowd-sourced consulting.
Who are the certified experts?
Our certified Experts are CTOs, CISOs, and Technical Architects who answer questions, write articles, and produce videos on Experts Exchange. 99% of them have full time tech jobs - they volunteer their time to help other people in the technology industry learn and succeed.
How quickly will I get my solution?
We can't guarantee quick solutions - Experts Exchange isn't a help desk. We're a community of IT professionals committed to sharing knowledge. Our experts volunteer their time to help other people in the technology industry learn and succeed.
How to enable remote access to a server?
Right-click the server, and then click Configure and Enable Routing and Remote Accessto start the Routing and Remote Access Server Setup Wizard. Click Next.
How to reconfigure a server?
To reconfigure the server, you must first disable Routing and Remote Access. You may right-click the server, and then click Disable Routing and Remote Access. Click Yes when it is prompted with an informational message.
How to create a group VPN?
Create a group that contains members who are permitted to create VPN connections. Click Start, point to Administrative Tools, and then click Routing and Remote Access. In the console tree, expand Routing and Remote Access, expand the server name, and then click Remote Access Policies.
How to connect to a dial up network?
If they are, see your product documentation to complete these steps. Click Start, click Control Panel, and then double-click Network Connections. Under Network Tasks, click Create a new connection, and then click Next. Click Connect to the network at my workplace to create the dial-up connection, and then click Next.
Can you grant callbacks in Windows 2003?
Administrators can only grant or deny access to the user and specify callback options, which are the access permission settings available in Microsoft Windows NT 4.0. The remaining options become available after the domain has been switched to native mode.
How to install Remote Access Server?
On the server that will act as the Remote Access server, in the Server Manager console, in the Dashboard, click Add roles and features. Click Next three times to get to the server role selection screen. In the Select server roles dialog box, select Remote Access, click Add Features, and then click Next.
What group does DirectAccess belong to?
For a client computer to be provisioned to use DirectAccess, it must belong to the selected security group . After DirectAccess is configured, client computers in the security group are provisioned to receive the DirectAccess Group Policy Objects (GPOs) for remote management.
Introduction
Should You Use Static Or Dynamic Routing?
- The question of whether you should use static or dynamic routing is really a question of administrative overhead. In the end, the result of your network traffic being routed to the correct network should be the same, no matter what method you choose. With static routing, you must make an entry on your Windows Server for every network that will be routed by that server. Thus…
Static Routing in Windows Server 2008
- Static routing in Windows Server is nothing new. We have been using the route command for years. You can configure static routing in Windows 2008 Server using either the route command or using the GUI. However, if you use the Windows GUI interface, those routes will not be listed in the CLI interface, when you type route print. Thus, I highly recommend that if you are going to us…
Dynamic Routing in Windows Server 2008 Using RIPv2
- Earlier in the article, I talked about the benefits of configuring dynamic routing. So, now let me provide you the steps to configuring RIPv2 in Windows 2008: 1. The first step is to install the Routing and Remote Access (RRAS) role in Windows 2008 Server. If you go into the Add Roles Wizard, the RRAS role can be difficult to find because what you ...
Summary
- Windows Server 2008 has one solid static routing option and one scalable dynamic routing option – RIPV2. I discussed how OSPF has been removed from Windows 2008 (and how I feel about that). We talked about why you would use static routing versus dynamic routing. Finally, I showed you how to configure static routing with the route command and dynamic routing by installing RI…