hikvision remote access to change time

Access the IP camera via a web browser and navigate to Configuration > Advanced Configuration > System > Time Settings tab. From here simply fill in the time settings as you did with the NVR (shown on the screenshot in the previous section). Configure DST (Daylight Saving Time)

Full Answer

How to correct the time on my Hikvision DVR/NVR/IP camera?

If you see the time on your Hikvision DVR, NVR or IP Camera is not accurate, you can refer to the below guide on how to correct it. 1) Use your PC, open the web browser - Chrome, Firefox, Sarafi, etc. 2) Enter the local IP Address of your Hikvision DVR,...

How do I Find my Hikvision IP Camera IP address?

Download and install the SADP tool in your computer and just open it up to start the Hikvision IP camera configuration process. If your IP camera is correctly connected to your network it might get an IP from your router. If it doesn't, you can find the camera with its default IP address which is 192.0.0.64.

How do I remotely access my Hikvision device?

Introduction The following guide will guide you through the necessary steps to remotely access your Hikvision device with another PC, Laptop, Tablet, Smartphone or iPhone. Before proceed please connect your device to your router and obtain a computer that is already connected to the same router or LAN.

How do I avoid incorrect timestamps on Hikvision devices?

In order to avoid an incorrect timestamp, Hikvision devices use NTP (Network Time Protocol) as well as DST (Daylight Saving Time) to adjust the device’s time. To have the right timestamp, you need to find the address of a reputable NTP server.

See more

How can I control hikvision remotely?

Go the following menu location: Configuration --> Network --> Platform Access. PRODUCTS: HIKVISION DEVICES TOPICS COVERED IN THIS KBA: How to enable Hik-Connect remote access on HIK devices (NVR/DVR/Camera). c. Select the Enable tick box at the top of the page.

How do I reset my Hikvision DVR remotely?

0:000:23Hikvision reboot - YouTubeYouTubeStart of suggested clipEnd of suggested clipAnd VR or DVR. Once you are logged in to the unit click on any configuration tab at the top. ClickMoreAnd VR or DVR. Once you are logged in to the unit click on any configuration tab at the top. Click on the maintenance menu on the left hand side then click on the reboot button at the top.

How do I change the date on my Hikvision NVR?

What is this? Access your NVR via a web browser and navigate to Configuration > System > System Settings > Time Settings tab. Fill in the required fields with the details you'll be using and hit save. Don't forget to test your NTP server.

What is NTP in hikvision?

Purpose. Sometime the device date/time may be incorrect. In order to avoid this, HIKVISION devices use NTP (Network Time Protocol) as well as DST (Daylight Saving Time) to adjust device time.

What is remote Configuration in HIK connect?

After adding a device, you can set the parameters of the device, including basic information, time settings, recording schedule, etc. Edit Information of Cameras Linked to Added Device. Set Video and Image Encryption.

How do I turn off HIKVision NVR remotely?

Log into the interface, right click, click Menu. In the bottom left you will see a small red power button. Press that and it will give you Shutdown/Restart options.

How do I change the date and time on my DVR?

0:211:10How to Change the Time & Date on DVR - YouTubeYouTubeStart of suggested clipEnd of suggested clipMake sure you're - you know if your date is wrong you can select it and just click on the calendarMoreMake sure you're - you know if your date is wrong you can select it and just click on the calendar day whichever is correct and press apply.

How do I change my IP camera time?

To correct the time instantly, go to IP Camera > Edit > Optimization and enable force synchronization. You can also go to the web UI of the camera, manually configure the time settings first, and then enable synchronization with the NTP server.

How do I change the time on my camera?

Every camera manufacturer has a different place in the camera's menu for setting the date and time; however, you can be certain that you will find the settings somewhere in the camera's menu. Look for a menu item labelled “date/time,” “setup,” “settings,” “tools,” or something similar.

What is the NTP server IP address?

NameIP AddressStatusntp-b.nist.gov132.163.96.5Authenticated servicentp-wwv.nist.gov132.163.97.5Authenticated servicentp-c.colorado.edu128.138.141.177Authenticated servicentp-d.nist.gov129.6.15.32Authenticated service

What is DST mode?

Daylight Saving Time (DST) is the practice of turning the clock ahead as warmer weather approaches and back as it becomes colder again so that people will have one more hour of daylight in the afternoon and evening during the warmer season of the year.

How does iVMS sync time?

On iVMS-4200 Checked the system you wish to sync the time and click on ok. If the system is online, the iVMS-4200 software will update the date/time of the system. Under General->Auto Time Adjustment, select the daily timing you wish the iVMS-4200 software to update all your CCTV's date/time on a daily basis.

How can I reset my HIKVision DVR without password?

0:324:114 Ways to Set You Free From Password Resetting - YouTubeYouTubeStart of suggested clipEnd of suggested clipEmail run hi connect app on the mobile. Phone tap more button to find reset device password to scanMoreEmail run hi connect app on the mobile. Phone tap more button to find reset device password to scan the qr code on device. The verification code will be sent to the reserved.

How do I reboot my DVR?

How to Reset a DVRTurn off your television. Video of the Day. ... Remove the power cable that supplies electricity to your DVR box.Leave the unit unplugged for at least a full minute.Insert the power cable back into your DVR.Tip. Some DVR brands, such as TiVo, also provide a menu-driven method for resetting the device.

How can I recover my HIKVision admin password?

1:455:00Hikvision Device Password Reset using SADP - YouTubeYouTubeStart of suggested clipEnd of suggested clipRight click on the sadp. Tool. And then left click run as administrator. Now it's asking us if weMoreRight click on the sadp. Tool. And then left click run as administrator. Now it's asking us if we want to enable update checking for the program let's enable it to the left of the id number left click

What is the default password of HIKVision DVR?

admin 12345Surveillance Brands - Default Username and PasswordsBrandUser NamePasswordHIKVisionadmin12345Honeywelladministrator1234IOImageadminadminIPX-DDKrootAdmin or admin26 more rows

How to check IP address availability?

a)You can check the IP address availability by performing the “Ping” command (Fig. 2). In order to do that you need to type ping 192.168.1.4 at the command promptwindow.

Where is the ipconfig command?

b) Windows NT, 2000, and XP users:  Locate the Windows icon in the bottom left corner of the task bar.  Click Run.  Type cmdor commandand press enter.  Following the available prompt, type ipconfigand press Enter.

Can you enable DHCP in DVR?

a) You can enable the DHCP checkbox in the DVR Network Configuration interface:

Can I remotely access my Hikvision device?

The following guide will guide you through the necessary steps to remotely access your Hikvision device with another PC, Laptop, Tablet, Smartphone or iPhone. Before proceed please connect your device to your router and obtain a computer that is already connected to the same router or LAN. Also make sure that your computer can access the internet. After properly port-forwarding (also called port-mapping) your router you will be able to access your device by using an internet browser, such us IE, Chrome, Firefox or Safari and/or our client software iVMS4200.

How to access Hikvision camera?

Open the camera via a web browser. After configuring the Hikvision IP camera address , just open a web browser such as Google Chrome, Mozilla Firefox, or Internet Explorer and type the camera IP address in the URL bar . If this is the first time you are trying to have access to a Hikvision camera, your browser will ask you to install a plugin ...

What is the IP address of Hikvision?

The picture shows that the SADP tool found the Hikvision IP camera in the network and the IP is 192.0.0.64, the communication port is 8000.

What is the IP address of a camera?

If it doesn't, you can find the camera with its default IP address which is 192.0.0.64. You can see that in the SADP tool.

Is it rocket science to configure an IP camera?

No worries, configuring an IP camera is not rocket science. There are a lot of different IP camera brands out there, but the configuration process is similar to all of them. In this article, I will teach you how to configure Hikvision IP camera.

Does Hikvision require a plugin?

If this is the first time you are trying to have access to a Hikvision camera, your browser will ask you to install a plugin (see the picture below).

How to see Hikvision equipment on network?

1) On your computer open SADP Tool. This program will show you any Hikvision equipment connected directly to your network. You should see a screen like the one below.

How to find serial number on a hik connect?

2) Click on the Add button in the top right corner and, in the window that pops up, enter the 9 digits from the Serial Number that you noted down earlier and press the Search button.

How to connect NVR to router?

Connect your NVR to your network by running an ethernet cable from the LAN port on your NVR or DVR directly to your router.

Can Hikvision cameras be used on NVR?

Make sure that your Hikvision system is set up locally and that your cameras are viewable on your NVR or DVR. If you have not already set your device up please follow the relevant guide on this page to do so.