Below are detailed instructions for how to setup remote access. • Assign your DVR a static IP Address on your network. This can be configured by accessing the Main Menu, click the Advance Icon and then click the Network Icon.
Full Answer
Can I access my H264 DVR from my mobile phone?
Therefore there must be a distributor that can support you with software for remote DVR remote viewing. Do you have a branded or non-brand DVR? To access your H264 DVR from your mobile phone, you first need to know if it has a brand.
How to configure DVR for remote viewing?
How to configure DVR for remote viewing 1 The types of DVR remote viewing. You can install the security cameras and set up the DVR using the manufacturer instructions and its cloud service or you can use port ... 2 Port forwarding for DVR remote viewing. ... 3 Video: Port forwarding for DVR remote viewing. ... 4 Extra information. ...
Why can't I access my DVR from outside the network?
Make sure you access the DVR while you are not inside the location as the DVR, due to the fact that many routers will not allow you to access internal devices from within the network using the external IP Address. I hope these steps will guide you through setting up your Network devices and DVR for remote access.
How do I change the default port on my DVR?
Go to the DVR's network menu and check which port is used for software. Let's say you are using a Dahua DVR, the default port is 37777 or if you are using a Hikvision DVR the default port is 80000. Make sure to check your DVR. Open your web browser again and use the port for the configuration.
How do I setup my DVR for remote viewing?
How to Remote Access a DVRCreate and Configure a Dynamic DNS Account.Set Up a Dynamic DNS on the Router.Connect the MPEG-4 DVR and Locate the DVRs IP Address.Setting up a Virtual Service on the Router.Install the Remote Viewer Software for Remote Internet Access.
How do I setup my H 264 DVR?
0:004:15H.264 Surveillance DVR Setup - YouTubeYouTubeStart of suggested clipEnd of suggested clipNext plug the camera power cable into the DVR and connect to a power source the DVR will boot up youMoreNext plug the camera power cable into the DVR and connect to a power source the DVR will boot up you should see a live view of your cameras on the screen. Press the menu button on the DVR or remote.
How can I view my CCTV from anywhere?
How to view your IP camera remotely via a web browserFind your camera's IP address. ... Open a web browser and type the IP address. ... Go to SETTING > BASIC > Network > Information to find the HTTP port number used by the camera.After you change the port, you will need to reboot the camera in order to save the changes.More items...•
How do I connect my H 264 DVR to my iPhone?
0:042:06View Security Cameras on iPhone - DVR-88xxRT - H.264 Standalone ...YouTubeStart of suggested clipEnd of suggested clipClick on that to get to the device list and then click on add for the name you can call it anythingMoreClick on that to get to the device list and then click on add for the name you can call it anything you. Want. Then for the address enter in the IP address. That you got from the DVRs.
What is the default password for H 264 DVR?
Most likely the default username will be admin and password: empty, 12345, or 123456.
What is App of h264 DVR?
The MEye is an application for DVR remote monitoring. It runs on Android and IOS devices and is very easy to install and setup.
Why can't I see my CCTV remotely?
What to Do If You Cannot Remotely View Security Cameras Using the Internet via Port Forwarding. Make sure your cameras are connected to the network. Ensure all the ports of the network configuration are mapped to the Internet. Open the firewall in the router to allow Internet access to the camera.
How can I remotely access my DVR without static IP?
Step1: Login Camera on Web Browser > Now Go to Config Tab > Network > Put HTTP Port and Server Port - By default HTTP Port 80 assign (i.e 81 and 6036)> Check mark on use the Following IP Address > Assign IP Address on Camera as given example > Apply.
How do I access my security cameras from an IP address?
1:384:35How to Find the IP Camera Address & Set up Port Forwarding ... - YouTubeYouTubeStart of suggested clipEnd of suggested clipNow let's see how to remotely. Access your camera using the ip address via a web browser. PleaseMoreNow let's see how to remotely. Access your camera using the ip address via a web browser. Please note that real link battery powered cameras don't support remote access via the ip. Address you need to
How can I control my DVR from my phone?
0:316:00How to connect to a DVR using an Android Phone - YouTubeYouTubeStart of suggested clipEnd of suggested clipChoose manual add and then input the information of the DVR for the name you can use any name thatMoreChoose manual add and then input the information of the DVR for the name you can use any name that is intuitive to you the address in this case we're going to use the internal IP of the DVR.
How can I access my CCTV on mobile?
HOW TO CONNECT CCTV TO ANDROID OR IPhone ?Step 1: CONNECT DVR TO MONITOR DIRECTLY. ... Step 2: CONFIGURE CCTV DVR SETTINGS. ... Step 3: NOW CONFIGURE WIFI ROUTER FOR DVR. ... Step 4: CONNECT DVR TO WIFI VIA LAN CABLE. ... Step 5: CHECK THE SETTINGS. ... Step 6: NOW CONNECT TO ANDROID PHONE. ... 1 Person Made This Project! ... 74 Comments.
How do I connect my DVR to WiFi?
0:473:10How to Connect a CCTV DVR to a Wireless Router - YouTubeYouTubeStart of suggested clipEnd of suggested clipThe DVR is hardwired to my wireless bridge using a cat5e cable. I am using an AP 3500 for my Wi-FiMoreThe DVR is hardwired to my wireless bridge using a cat5e cable. I am using an AP 3500 for my Wi-Fi bridge which is a multi-purpose wireless.
What is the default password of DVR?
The default passwords for your DVR or NVR are the same as the username.
How do I reset my DVR to factory settings?
To factory reset the device, unplug the DVR from power. Once power is removed from the unit, press and hold the factory reset switch for 4 - 5 seconds, continue holding the reset switch and plug the DVR's power supply back into the unit, you will hear a beep.
Why does my CCTV says no signal?
A CCTV test monitor is extremely helpful when troubleshooting camera video issues. One of the most common problems when a camera is not displaying video is a bad cable or BNC connection. Using a test monitor, you can temporarily eliminate the power and video cable that your camera is using.
How do I connect my CCTV to the Internet?
Connect Your CCTV Device to the Internet (DVR or NVR)Step 1: Securing Your Device and Establishing Internet Connection. ... Step 2: Indirect Connection (Mobile APP) ... Step 3: Indirect Connection - PC Browser. ... Step 4: Direct Connection - Setup. ... Step 5: Direct Connection - Mobile APP. ... Step 6: Direct Connection - PC Browser.
How to access DVR from outside network?
The default username is admin and the password is admin. Click login, then you will see the page of your Web Service. To access the DVR from outside the network or externally, the steps will be the same but the IP address will be your external IP address.
What is the IP address of a DVR?
By default ALL of our recorders and IP cameras have the same IP address. The default IP address is 192.168.1.108.
How to know if your DVR is on the same network as your home network?
First, you must review your network scheme to identify if your DVR or IPC (IP camera) is within the same network scheme as your Home/Office Network. There are a few ways to identify your network by simply going to the “Command Prompt” in your Windows PC.
What happens if you assign an IP address to a DVR?
This is due to the fact that if you assign an IP address to the DVR, NVR or IP camera that is already being used by a computer (hard wired or wireless), printer, or even a wireless handheld device you will have a collision in your network and you will not be able to access the device. In the next step I will show you how to see what IP addresses are available for you to use with your Digital Video Recorder.
Can I access my DVR from my router?
Make sure you access the DVR while you are not inside the location as the DVR, due to the fact that many routers will not allow you to access internal devices from within the network using the external IP Address. I hope these steps will guide you through setting up your Network devices and DVR for remote access.
What port is remote viewing on a DVR?
As you can see, now it's possible to use the DVR remote viewing feature using a web browser (port 8080) or a software (port 37777).
What is the default port for a DVR?
Go to the DVR's network menu and check which port is used for software. Let's say you are using a Dahua DVR, the default port is 37777 or if you are using a Hikvision DVR the default port is 80000. Make sure to check your DVR. Open your web browser again and use the port for the configuration.
Can you use the same principle to configure IP cameras for remote viewing?
You can use the same principle to configure IP cameras for remote viewing.
Can you add videos to your watch history?
Videos you watch may be added to the TV's watch history and influence TV recommendations. To avoid this, cancel and sign in to YouTube on your computer.
Can you configure a router?
As long as you have the necessary information you can configure the router.
Works with Analog CCTV and HD Security Cameras
Hybrid iDVR-PROs work with the following security camera types and resolutions.
Request a Demo
If you do not currently have an iDVR-PRO and would like to log in to the demo unit at our office, please request a demo login below. You will be able to login from iPhone, iPad, and Android mobile devices. You can also login from Macintosh and Windows computers. Please click here to request a demo login .
Complete CCTV Systems
Did you know? CCTV Camera Pros can provide a complete surveillance system quote that includes any iDVR-PRO model with cameras, cables, connectors, power supplies, and monitors? We can even mix and match SD and HD security cameras because the latest iDVR-PROs are hybrid. They work with CCTV, AHD, and HD-TVI type cameras.
How to access H264 DVR?
To access the H264 DVR directly on your mobile phone, go to the playstore and install the App. See the images below. Make sure you are your are downloading the correct version of the Meye app, because in Playstore there are other similar apps. Download the App that is developed by Meyetech.
What is a H.264 DVR?
Some DVRs have the following names in the front part: Network H.264 DVR. H.264 Digital Video Recorder. Digital H.264 Recoder. H.264 DVR. There are other variations of the name, but none of them represents the brand but rather the type of compression (CODEC) that it uses. They are non-branded DVRs manufactured in China and passed to ...
Why is my DVR not connecting to the internet?
If the application stays for a long time showing the message "connecting" something is wrong with the Internet link, it may be slow or maybe some firewall is blocking the DVR from the Internet or internal network.
Where is the Alartec logo on a DVR?
We will use the Alartec brand as a DVR brand example, when you purchase an equipment from that company you can see the logo somewhere, usually on the frontal part of the DVR and also on the configuration menu.
Is the installation of a symlink fast?
The installation is simple and very fast, but bring the adds with it.
Is H.264 a brand?
I do not know exactly what might be written on the front part of your DVR, but I can assure you that H.264 is not a brand!
Do you have a branded or non-brand DVR?
To access your H264 DVR from your mobile phone, you first need to know if it has a brand. If it's a branded model probably it will have an operation manual and a technical support number, which is very good.