What is the default admin password for the sbg6580-2?
NOTE: On later versions of the SBG6580-2, the Wi-Fi Security Key is used as the default admin password printed on the bottom while label. For assistance with Web Manager Access, refer to article # 18752 – SBG6580-2: Web Manager Access. Click the Login button. The Home page will appear.
How do I Turn on the SBG6580?
This turns on the SBG6580. Once the power cable is plugged into your device and connected to the power supply, the modem should light up revealing various icons on it. Ready to go. Allow the gateway five to thirty minutes to find and lock on the appropriate communications channels after the gateway is on.
How does the SURFboard SBG6580 primary network wireless functionality work?
On the SURFboard SBG6580 wireless gateway, the primary network wireless functionality is enabled by default – with WPA-PSK encryption for security. This allows any wireless clients associated with the primary network to communicate with other wired or wireless clients on that primary network.
How do I block remote access to my router?
To do this, open your router's web interface and look for the “Remote Access,” “Remote Administration,” or “Remote Management” feature. Ensure it's disabled — it should be disabled by default on most routers, but it's good to check.
How do I reset my Arris router remotely?
The easiest method is to open the browser and log in as an administrator.Open a web browser and connect to your home router as an administrator. ... Once you're logged into your router as administrator, you can usually find the option to reboot your router in the Advanced section of the router's menu.More items...•
How do I turn off the wifi on my Arris SBG6580?
1:1721:47How to Disable the Motorola SBG 6580 Router - YouTubeYouTubeStart of suggested clipEnd of suggested clipSo go to wireless. And we'll go to primary Network. Then you're going to go to primary. Network dropMoreSo go to wireless. And we'll go to primary Network. Then you're going to go to primary. Network drop-down and select disabled. Then click on apply on.
How do I setup my Arris modem SBG6580?
Install the SBG6580. Connect the coaxial cable to a cable wall outlet (if not connected) and the Cable connector on the rear of the SBG6580. Hand-tighten the connectors to avoid damaging them. Connect the Ethernet cable to the Ethernet port on the computer and to the Ethernet port on the rear of the SBG6580.
How do I access my Arris router remotely?
To Enable Remote Access Enter http://192.168.0.1 into the address box, and press the Enter key. The Login page will appear. NOTE: A security or private risk alert may appear on the web browser advising users to proceed with caution when accessing the Web Manager. There is no risk in proceeding to the Web Manager.
How do I reset my Arris surfboard sbg6580?
Factory Reset Carefully insert the tip of a pen or an unwound paperclip into the reset switch and press on to it. Hold down the Reset switch for 5 -10 seconds and release it. NOTE: To assure the gateway factory defaults, hold the reset switch for 5 -10 seconds. The indicators are that all LEDs turn off.
How do I turn off the wifi on my Arris surfboard?
Arris TG862First step is to open Arris TG862 web interface at http://192.168.0.1.Log in using admin as user, password as password.In the Basic Setup tab, you will have to disable wireless.Click on Apply (notice that modem Wifi light will go off).
Can I use SBG6580 as modem only?
The SBG6580-2 serves as a modem and a router and keeps the devices in the Local Area Network (LAN) hidden. In certain situations, it may be desired to disable the router function of the SBG6580-2, and have it operate as a modem only. This can be accomplished by configuring the SBG6580-2 for Bridge Mode.
How many devices can connect to Motorola SBG6580?
By default, the SBG6580 operates as a gateway, and provides Internet access for multiple devices (up to 245 devices), connecting to the SBG6580 gateway.
What is the default password for Arris SBG6580?
passwordWhen attempting to access the SBG6580-2 Web Manager for the first time, the SBG6580-2 prompts for an admin username and password. By default, the username is admin, and the password is password.
How do I log into my Arris router SBG6580?
Enter http://192.168.0.1 into the address box, and press the Enter key. The Login page will appear. On the Login page, enter admin in the Username field.
What is bridge mode on Arris modem?
Bridged Mode This means that the modem will act as a bridge, i.e. the public IP (IP address assigned by the ISP) is going to be taken by the customer equipment such as the router instead of the modem.
Can you reset a router remotely?
You can do this kind of remote management by entering the wireless router's IP address into a standard web browser, logging in with your network credentials such as default username and password. Look for a setting devoted to resetting the wireless router or restoring it to its factory default settings.
How do you reset your router from your computer?
Steps to Reboot a Router and ModemUnplug the router and the modem. ... Wait at least 30 seconds. ... Plug in the modem. ... Wait at least 60 seconds. ... Plug in the router. ... Wait at least 2 minutes. ... When the router and modem restart, test to see if the problem went away.
Why is my Arris modem not connecting to WIFI?
Unplug power cord from gateway for 30 seconds and then plug it back in. Check if power cord is damaged. If the cord is connected to a power bar, try connecting it directly to the wall outlet. Try another power outlet.
How do I reset my Arris router username and password?
Set a new passwordOpen a web browser.Enter "192.168. ... Enter the username "cusadmin" (lowercase).Enter the current password (case sensitive) found on the white sticker on your modem.Click Manage Wi-Fi Network.Click the 2.4G or 5G tab, for the network you want to set a new password.More items...
What is bridged mode on a SBG6580?
For your SBG6580, you may opt into the bridged mode when: Adding a router, firewall, or another NAT device to manage your Local Area Network, or; Hosting applications or services that can benefit from being directly accessible from the Internet.
What is the purpose of the SBG6580?
Normally, the SBG6580 serves as a modem and a router and keeps the devices in the Local Area Network (LAN) hidden when NAPT mode is enabled . Disabling the NAPT mode however serves to turn off the “router” function and the device directly connected to the SBG6580 get to receive the Public IP address from the cable network provider.
How to log in to Motorola?
At the Login prompt, enter ‘admin’ in the username field and ‘Motorola’ in the password field. Then click the Login button.
What does it mean to leave a login on Motorola?
By default, the logins are usually: Admin (for username) Motorola (for password) Leaving the logins like that will mean that anyone with a computer and internet can gain access to your account and mess things up. So, head over to the Security tab.
How to connect a SBG6580 to a power supply?
Plug the power cord into the power connector on the SBG6580. Plug the power cord into the electrical outlet. This turns on the SBG6580. Once the power cable is plugged into your device and connected to the power supply, the modem should light up revealing various icons on it. Ready to go.
How to get your modem on your records?
Time to call up your cable company to have them list your modem on their records. They will usually ask you a couple of questions about your device so they can give it access to their internet service. Provide them with that information, often certain numbers on the device, and they will hook you up in no time.
What is the status page of a modem?
On this default page you will find the information that offers a snapshot of a series of events that the modem goes through when establishing a connection to your cable internet service provider (ISP).
Funny (not really) vendor story
I purchased a LTaP for personal use awhile back, paid for with my personal card and shipped to my house. When it arrived it didn't quite have that 'straight from Mikrotik' freshness but I didn't think anything of it (after all, who among us hasn't gone out to the warehouse to 'look' at inventory lol).
RouterOS 7 and AT&T Fiber Bypass (with dot1x)
It can still be done, even though the 'default-vlan-id' option (even though it's still documented...) doesn't work in ROS 7.
What happened to the Docker support in ROSv7?
I just bought Unifi U6-LR, and need to configure a Unifi Controller to set it up with RB5009. I recall seeing Docker Container support on one of the 7.1 betas, so I was planning to use that to run Unifi Controller on Mikrotik. Unfortunately, it seems like the Docker support has been removed on stable release.
Manage multiple remote Mikrotiks? VPN? Wich one? How to deploy solution to multiple sites
It's getting harder and harder for me to manage my Mikrotik devices by going on site, especially since I've deployed several wifi LANs with capsMAN, etc.
Summary
This article provides instructions on how to setup your Wireless Network, recommended settings, and how to connect other devices to your wireless network.
Solution
In order to manage and setup your Wireless Network you will need to login into the Web Interface on your Arris Gateway.
Logging into the web interface
Open up a web browser (Internet Explorer, for example) and enter the IP address http://192.168.0.1 in your browser’s address bar and press Enter.
Setting your Wireless Settings
On the first initial page, you will see all of your Wireless settings.
Recommended Wireless Settings
These are settings that are recommended if you are uncertain what settings you should select.
Connecting other devices via Wireless
You can manually enter in the security Passphrase or Network Key. To do this, it will depend on your operating system.
How to login to SR400?
Open a web browser and enter http://192.168.1.1 in the browser address bar. The SR400 administration interface should load . To login to the router, enter the default username and password (Default admin/admin respectively).
Where is the WiFi connection on arris?
Once logged into the Arris interface, select the Gateway menue on the left hand side of the page, then WiFi under the Connection subsection.
How to login to a router?
To login to the router, enter the default username and password (Default admin/admin respectively). Select the Wifi tab from the top of the page. Select the 2.4Ghz Wireless option and shift the Enabled slider to the left to disable it, then repeat the same action under the 5Ghz Wireless option.
How to enable wireless router on 2.4GHz?
Enter the your admin username and password. The default user name and password are admin and password, respectively. Click on the Advanced tab. Click on the Advanced Setup menu and then Wireless Settings. Uncheck the Enable Wireless Router Radio for both the 2.4GHZ and 5GHZ networks. Click on Apply.
How to log into router GUI?
Log into the router's GUI on Web by typing in 192.168.1.1.
How to check if my router is 168.2.1?
Enter " http://router" " or the router's default IP address, " 168.2.1 " in the Address bar and press [Enter ] . If it doesn't work, check your router's IP address.
