Remote-access Guide

how to enable remote access to a aurba 2390f

by Birdie Altenwerth Published 2 years ago Updated 2 years ago
image

How to configure Aruba utilities to connect to the AP?

Video of how to configure the Aruba Utilities application and Connect to the AP in console mode are below: When in the Aruba Utilities android app, you need to go to settings and make sure Enable Bluetooth Scanning is enabled. Navigate to Ibeacons and try to find the corresponding Aruba Ibeacon that is your AP.

How to enable Bluetooth scanning in the Aruba utilities Android app?

When in the Aruba Utilities android app, you need to go to settings and make sure Enable Bluetooth Scanning is enabled. Navigate to Ibeacons and try to find the corresponding Aruba Ibeacon that is your AP.

Why can't I access the console port of my Aruba AP?

Many times you need to access the console port of an Aruba AP but cannot, because you either don't have the cable or you physically cannot access the access point console port. Below is a video of how you can connect to the console of the access point using Aruba Utilities using an Android device and bluetooth.

How do I onboard my Aruba INSTANT ON switch to a site?

The following procedure is a step-by-step process of the initial setup to onboard Aruba Instant On switches to a site: 1. Ensure that the Instant On switch is connected to the internet to be discovered. 2. Connect the port you want to use as your switch uplink to your local network using an Ethernet cable, then power it on.

image

How do I access my Aruba Access Point remotely?

Navigate to Configuration > AP Installation (under Wireless.) Select the required remote AP under the Provisioning tab and then click Provision. Select Yes for Remote AP and Certificate for Remote AP Authentication Method. Click Apply and Reboot to apply the configuration and reboot the AP as certificate RAP.

How do I enable web management on Aruba switch?

Use the command https-server to enable the web server and set the access mode, and then establish a connection to the management port using a web browser. When prompted, login with the admin account.

How do I access the web interface in Aruba?

Start a supported web browser and enter the IP address of the management port in the address bar. Use HTTPS.Optionally a pre- and post-login message may be displayed. ... At the login page, enter your user name and password credentials, then click Login.After you log in, the main Web UI page is displayed.

What is Aruba Remote Access Point?

Remote_AP. The Secure Remote Access Point Service allows AP users, at remote locations, to connect to an Arubacontrollerover the Internet. Since the Internet is involved, data traffic between the controllerand the remote AP is VPN encapsulated. That is, the traffic between the controller and AP is encrypted.

How do I enable web interface on HP switch?

To enable web login, log in to the device via the console port, and perform the following configuration: • Enable HTTP or HTTPS service • Configure the IP address of the VLAN interface • Configure a username and password The device supports the following web login methods: • HTTP login: • HTTPS login: The following ...

How do I configure Aruba management interface?

Use the command ip dhcp to configure the management interface to automatically obtain an address from a DHCP server on the network (factory default setting). Or, assign a static IPv4 or IPv6 address, default gateway, and DNS server with the commands ip address, ipv6 address, ip static, default-gateway, and nameserver.

How do I configure my Aruba access point?

Configuring Access Point (AP) settingsClick Configuration, Wireless.Select a group and then click Access Points. ... Click the AP that user want to customize.Click Edit. ... Configure the parameters described in table below as required and then click Save Settings. ... Click Save Settings and reboot the AP.

How do I connect to Aruba switch?

To connect a console to the switch, use the RJ-45 console cable shipped with the switch. Alternatively, user can use a USB cable (Not supplied) for a console connection. (See USB Console Port Notes below.) Connect a PC or VT-100 terminal to either of the Console ports.

How do I find my Aruba access point IP address?

Viewing Access Point Details Tap any of the APs listed in the Inventory list. The Access Point Details page is displayed with details. View the AP details such as the AP name, IP address of the AP, MAC address, Serial number, AP type, radio, and the number of the clients connected on each radio channel.

Which devices can access remotely in networking?

Remote access gateway devices can be computers running remote access software and connected through multiport serial boards with 4, 8, 12, or more asynchronous communication ports that are connected to analog modem banks or ISDN terminal adapters, or they can be routers with built-in modem or Integrated Services ...

What is the differences between remote access and site to site VPN?

A remote access VPN connects remote users from any location to a corporate network. A site-to-site VPN, meanwhile, connects individual networks to each other.

How do you set a 2930M switch in Aruba?

The 2930M command-line prompt should be displayed on the console screen, typically with the switch model number (For example, Aruba 2930M#)....Reconfigure the switch and save the new settings.Exit from the console session.Reconfigure the terminal and save the new settings.Begin a new console session.

What does Aruba AirWave do?

AirWave provides detailed health and analytics dashboards to monitor critical applications and services, including: Network Health – used to view client usage, monitoring and configuration compliance, alert summaries and other selected statistics.

How do I setup my Aruba Instant AP?

To configure device parameters on an access point (AP), complete the following steps:In the Network Operations app, select one of the following options: ... Click the Config icon. ... Click the Access Points tab. ... To edit an AP, select an AP in the Access Points table, and then click the edit icon.More items...

How do I connect to Aruba switch?

To connect a console to the switch, use the RJ-45 console cable shipped with the switch. Alternatively, user can use a USB cable (Not supplied) for a console connection. (See USB Console Port Notes below.) Connect a PC or VT-100 terminal to either of the Console ports.

Notices

The information contained herein is subject to change without notice. The only warranties for Hewlett Packard Enterprise products and services are set forth in the express warranty statements accompanying such products and services. Nothing herein should be construed as constituting an additional warranty.

Acknowledgments

Intel ®, Itanium ®, Pentium ®, Xeon ®, Intel Inside ®, and the Intel Inside logo are trademarks of Intel Corporation in the U.S. and other countries.

Does Aruba support sequence sensitive commands?

The Instant CLI does not support positioning or precedence of sequence-sensitive commands. Therefore, Aruba recommends that you remove the existing configuration before adding or modifying the configuration details for sequence-sensitive commands. You can either delete an existing profile or remove a specific configuration by using the no… commands.

Does Aruba support 4k buffer size?

The CLI does not support the configuration data exceeding the 4K buffer size in a CLI session: therefore, Aruba recommends that you configure fewer changes at a time and apply the changes at regular intervals.

image
A B C D E F G H I J K L M N O P Q R S T U V W X Y Z 1 2 3 4 5 6 7 8 9