Note: In Packet Tracer, enter the crypto key generate rsa command and press Enter to continue. RTA (config)# crypto key generate rsa The name for the keys will be: RTA.CCNA.com Choose the size of the key modulus in the range of 360 to 2048 for your General Purpose Keys. Choosing a key modulus greater than 512 may take a few minutes.
Full Answer
How do I configure a Cisco router in Packet Tracer?
After adding a Cisco Router, Switch, and PC on the Packet Tracer workspace, cabling all devices. Double-click Cisco Router1 to open the CLI prompt and type No to skip the initial configuration and press Enter.
Can Packet Tracer take control of the other host?
Sorry for the broad answer, I don't think / remember that packet tracer had a option in their hosts to take control of the other. A wireless network has to be designed at home with remote access from office. There are 3 users at home. Two users have a desktop and the third user has a laptop.
How does Packet Tracer (PT) work?
In this Packet Tracer (PT) activity, you will configure a remote-access VPN client to connect a laptop in the Cafe to a network in the Data Center. You will then use a “sniffer” to observe unencrypted and encrypted traffic. The Cafe is a popular place for remote workers.
Is it possible to run RDP from Packet Tracer?
If you are expecting / expected to run a Windows like RDP within packet tracer I don't think that is possible.
How do you remote access a switch?
Step 1 From the remote host, enter the telnet command and the name or IP address of the switch you want to access. Step 2 At the prompt, enter the password for the CLI. If no password has been configured, press Return. Step 3 Enter the necessary commands to complete your desired tasks.
How do I access my packet tracer router?
Step1: Open the Cisco Packet Tracer. Step2: Drag and drop any series of the router from the bottom of the interface into the middle of the working area. Step 3: Select cable from the bottom of the interface to connect the routers. Step 4: Click on Router R0, then on CLI.
How do I configure my router for remote access?
All you need to do is type the router IP or default gateway address in the web browser. Next, enter your username and password. Now, once you are in the router's web portal, look for the Remote Management option. Some routers called it Remote Access and it's usually found under Advanced Settings.
How do I manage a remote switch?
To prepare a switch for remote management access, the switch must be configured with an IP address and a subnet mask. Keep in mind that to manage the switch from a remote network, the switch must be configured with a default gateway. This is very similar to configuring the IP address information on host devices.
Does SSH work in Packet Tracer?
Configuring SSH on a router in Packet Tracer First build the network topology. Both the hostname and domain name will be used in the process of generating encryption keys. 3. Now generate encryption keys for securing the session using the command crypto key generate rsa.
What is SSH in Cisco Packet Tracer?
SSH (Secure Shell) is one of the most used protocols in network World. As a secured alternative of Telnet, SSH is always in the life of a network engineer. It helps us to connect our routers, swithces and any other network equipments. Especially because of SSH is more secure, it is always prefered more than Telnet.
How do I access a remote IP address?
Remote Desktop to Your Server From a Local Windows ComputerClick the Start button.Click Run...Type “mstsc” and press the Enter key.Next to Computer: type in the IP address of your server.Click Connect.If all goes well, you will see the Windows login prompt.
How can I access my router from another network?
Here is a quick guide.Open your router's configuration.Click Advanced Settings on the left hand side.Click NAT.Click the Add button.Select the Custom Service radio button.In the Name field type something like Router Config.Enter 192.168. 1.2 as the server IP.For all External and Internal port fields type 80.More items...•
How can I access my computer from anywhere?
Set up remote access to your computerOn your computer, open Chrome.In the address bar, enter remotedesktop.google.com/access .Under “Set up Remote Access,” click Download .Follow the onscreen directions to download and install Chrome Remote Desktop.
How do I remotely control a Cisco switch?
0:2112:19Cisco router and switch configure remote access (telnet/ssh) - YouTubeYouTubeStart of suggested clipEnd of suggested clipFor telnet in the way we need to do that is we edit the vty lines Pete definitely BTY stands forMoreFor telnet in the way we need to do that is we edit the vty lines Pete definitely BTY stands for virtual terminal 0 to 15. And then we need to tell it we want set a password we'll set that to Cisco.
How do I access a Cisco switch?
Configuring the Switch Web GUIConnect your PC to the service port and configure an IPv4 address to use the same subnet as the switch. ... Start Internet Explorer 10 (or later), Firefox 2.0. ... On the Accessing Cisco Switch page, click the Wireless Web GUI link to access switch web GUI Home page.More items...
How do I login a switch using putty?
Configure putty to be able to communicate with the router over the USB port ( /dev/ttyUSB0 ).run sudo putty.Click on Serial for the Connection Type:Set the serial line to /dev/ttyUSB0.Click on Keyboard, then set backspace key to Control-H.Click on Session . Click on Default Settings. Click Save .Click Open .
How do I find the IP address of my Packet Tracer router?
Unzip the file and open the config file for the router.Scroll down in the file and look for the interface configuration section. Each line will begin with the word “interface”.Locate the interface you are interested in, for instance interface vlan10. Note the IP address configured for the interface.
How do I access my router through terminal?
Access router command line interface using Windows laptopUnder Category, choose Session.Under Connection type, choose Serial.In the Serial line, enter the COM port on your laptop that is connected to the console port on your router, using the console cable.Click Open.
How do I log into my Cisco wireless router?
Cisco router login:Make sure you're connected to your network.Open a browser, and go to 192.168. 15.1.Enter the username and password.Default login credentials.Next Up: Speed up your Wi-Fi connection.
How do I give an IP address to a Cisco Packet Tracer router?
Under global settings you will find a field for the gateway. Enter the corresponding IP address of the router's interface, which is 192.168. 10.1. Then click the FastEthernet tab on the left column to set the actual computer's IP address to be on the network.
Permanently disable service call-home 9300 ver 16.9
I've done no service call-home and no call-home, but it gets enabled after reboot by Smart Agent. How do I permanently disable this?
CCNA Labbing Equipment
Hello all! Currently I am looking for equipment to support my CCNA 200-301 certification study. What is the minimum/recommended lab setup for it? I am looking for the cheapest option possible too because it is pretty hard to find (used) Cisco devices in my country (Malaysia). Thank you!
Most convenient way to document configuration changes
We used to produce a file containing the detailed documentation for every change implemented for one of our customers on their appliances. This included every line of configuration prompted.
I Need Cisco Customer Rep
I'm hoping among the 56k+ members there might be someone who can help me. I have a customer that recently purchased two ASAs. The devices were registered under the wrong company. I've tried calling multiple times and no one seems to be able to help.
Dual mpls design with route redistribution
If I had 2 sites (site A and site B)... and the sites talk through mpls. And it looks like: site A L3 switch <-ospf-> cpe (with ospf/bgp mutual route redisitribution) <-bgp-> MPLS cloud <-bgp-> cpe (redistribution) <-ospf-> site B L3 switch. That part works fine.
How to configure telnet on Cisco router?
Step 1. After adding a Cisco Router, Switch, and PC on the Packet Tracer workspace, cabling all devices. Step 2. Double-click Cisco Router1 to open the CLI prompt and type No to skip the initial configuration and press Enter. Step 3.
How to connect to a telnet device?
At the CMD prompt, type telnet 192.168.1.1 and press Enter to connect to the device. Enter the user name and password you created during the setup of the connection.
What is the disadvantage of telnet?
The only disadvantage of Telnet is security. It sends data over the network without encrypting it, allowing spies to access data such as user names and passwords.
Can you review open sessions on Cisco router?
You can review open sessions on the Cisco Router.
Objective
The objective of this lab is to configure the switch for remote management such that the laptop PC residing on a remote network be used to login and manage it via ssh . To accomplish this, the following will be done:
Implementation
The following configuration commands will the required to configure a Cisco switch for remote management. The commands used here a for the lab represented in the network topology used here. However, the solution can be achieved in many different ways.
Verification
To verify that I have configured the Cisco switch for remote management via ssh, I try to access the switch using the laptop on the network 192.168.0.0/24 using ssh. Remember that both the laptop and the switch are on different networks. See the result below.
Telnet Operation
You might not always have direct access to your switch when you need to configure it. You need to be able to access it remotely and it is imperative that your access is secure. This topic discusses how to configure Secure Shell (SSH) for remote access. A Packet Tracer activity gives you the opportunity to try this yourself.
SSH Operation
Secure Shell (SSH) is a secure protocol that uses TCP port 22. It provides a secure (encrypted) management connection to a remote device. SSH should replace Telnet for management connections.
Verify the Switch Supports SSH
To enable SSH on a Catalyst 2960 switch, the switch must be using a version of the IOS software including cryptographic (encrypted) features and capabilities. Use the show version command on the switch to see which IOS the switch is currently running.
Configure SSH
Before configuring SSH, the switch must be minimally configured with a unique hostname and the correct network connectivity settings.
Verify SSH is Operational
On a PC, an SSH client such as PuTTY, is used to connect to an SSH server. For example, assume the following is configured:
Packet Tracer – Configure SSH
SSH should replace Telnet for management connections. Telnet uses insecure plaintext communications. SSH provides security for remote connections by providing strong encryption of all transmitted data between devices. In this activity, you will secure a remote switch with password encryption and SSH.