How do I disable AT&T router remotely?
access to your 2Wire gateway and home network. To disable Web Remote Access, uncheck the box. Change Password. To change your Web Remote Access password, enter and confirm your new password.
How do I enable remote access on my AT&T router?
Just log into your gateway using 192.168. 1.254. Once you're there select Remote Access on the top menu, enter your RG's Access Code and from there it gives you the option to setup. The user name will be tech and you will need to create a password.
How do I reset my pace 5268ac?
A factory reset will change all gateway settings back to default....To do so:Hold the red reset button on the back of the gateway down for 15 seconds.The Power LED will turn red. After 15 seconds it will turn green again. Let go of the reset button.Allow a couple of minutes for the gateway to reboot.
How do you put pace 5268ac in bridge mode?
3:4312:28GATEWAY BRIDGE MODE ROUTER SETUP (AT&T Pace 5268ac)YouTubeStart of suggested clipEnd of suggested clipOr your local Area. Connection. We're going to come over here to Wi-Fi. Once we are in Wi-Fi we'reMoreOr your local Area. Connection. We're going to come over here to Wi-Fi. Once we are in Wi-Fi we're gonna disable both 2.4 gigahertz and 2.5 gigahertz Wi-Fi radio bands and click Save.
What is remote access for ATT router?
AT&T Secure Remote Access allows administrators to grant access to specific applications by role or user without connecting to the network, helping to reduce risk of DDoS attacks or malware spread.
How do I change my AT&T router settings?
Modem & Router SettingsFrom a device that is connected to the AT&T Wireless Internet network, open the web browser then go to http://attwirelessinternet. ... ACCESS MODEM SETTINGS: Click the Wi-Fi tab then click Edit under the desired Wi-Fi frequency band.More items...
How do I reset my uverse remote control?
Enter programming code 981 by pressing the number keys on the remote control. The Power key will flash four times indicating the code was successfully entered and the remote has been reset to the default settings.
How do I reset my AT&T Pace router?
Gateway rebootShut down your computer.Locate the Reset button on the rear of the gateway, located beside the power input.Press and hold the button for 3 - 4 seconds. Note: Do not press the Reset button for more than nine seconds. ... Wait for the device to reboot and all LEDs to light up.
How do I reset my pace router?
The reset button can be found on the back of your Wireless Gateway. Press and hold the reset button for 3 seconds. Wait until the lights restore to their normal configuration. (Power, Wireless, Broadband 1, and Service lights should all be green).
Is IP passthrough the same as bridge mode?
IP pass-through works essentially the same as the bridged mode where customer can use their own router behind the ISP-provided gateway. However, in IP pass-through mode the signal is terminated (bridge mode signal is not terminated) at the gateway and allows the ISP to connect to the gateway with its own IP.
How do I change my AT&T router to bridge mode?
Alternate firmware version instructions:Open a web browser.Type 192.1. 68.1. ... Click the go button or press the enter key on the keyboard.Click the Broadband DSL Line button.Then click the Configure Connection button.Choose Bridge Ethernet from the Protocol drop-down.Click the Save and Restart Connection button.
How do I use bridge mode?
Toggle Bridge Mode On/OffEnter the default username and password: ... From the left-hand column, select Gateway > At a Glance.Next to Bridge Mode, click Enable.You'll see a message: "WARNING: Enabling Bridge Mode will disable Router functionality of Gateway and turn off the private WiFi network.More items...
How do I access my AT&T gateway settings?
Enter http://192.168.1.254 to access the gateway settings screen. Scroll to the Key things to do Using your Gateway and, select Wireless.
How do you I access my router settings?
Tap on the network name. Look for a 'gateway', 'router' or other entry in the list....Find router IP address on Android or iOSTap on Wi-Fi.Make sure your phone is connected to your router's Wi-Fi network.Tap the 'i' to the right of the network name.Your router's IP address is shown next to 'Router'
How do I enable UPnP on my AT&T router?
Enabling UPnP On AT&T RouterConnect the router to your PC with a wired or wireless connection.Here, you'll see a Home Network option. Click on the option to see your network devices.Finally, click on Access Shared Files next to the device and enable UPnP on it.
What can you do with an old AT&T router?
What You Can Do With an Old RouterWireless repeater.Guest Wi-Fi connection.Cheap internet radio.Use the old router as a network switch.Adapt it as a wireless bridge.Convert your router into a NAS.Use an old router as a web server.A DIY VPN router.More items...•
What is a Pace 5268?
Follow. The Pace 5268 is one of the Residential Gateways used for Fusion DSL and the primary gateway for Gigabit Fiber customers. It features four gigabit Ethernet LAN ports and a 4x4 MIMO 802.11AC wireless interface. Please note, a Pace 5268 is also provided for Fusion IP Broadband customers. Features and settings that are available for Fusion ...
How to log into modem?
Log into the modem's interface by surfing to http://192.168.42.1 (old versions of hardware that used original firmware use 192.168.1.254)
What does it mean when a device has no light?
No light indicates the device is not searching for a DSL signal.
Does Fusion have a Pace 5268?
Please note, a Pace 5268 is also provided for Fusion IP Broadband customers. Features and settings that are available for Fusion and Gigabit Fiber customers may not be accessible for Fusion IP Broadband customers.
Where is the password for my wireless gateway?
You may be asked to type in the password for your residential gateway. This can be found printed on a sticker below your wireless key on the side of your residential gateway.
Can you use your own router behind the pace gateway?
The recommended configuration if you'd like to use your own router behind the Pace residential gateway. This configuration allows a device plugged into a specified Ethernet port to bypass the Pace firewall and NAT table and obtain its own public IP address. This configuration will not work if your circuit has been assigned a single static IP address.
How to connect power adapter to gateway?
Connecting the power adapter Use the power adapter that was packaged with the gateway because it matches the power requirements of the gateway and it complies with local requirements 1. Connect one end of the power adapter to the POWER port on the gateway 2. Connect the other end to a power outlet. After the gateway is powered on, the power light blinks green for a moment and then turns steady green . Chapter 2 Setting up the Gateway
How to enable DMZplus mode?
C ick the Settings tab then click the Firewall tab Click Applications, Pinholes and DMZ Select the computer that you want to put in DMZplus mode If the computer you want to select is unlisted because it is powered off and the Hide inactive devices opton is enabled, you can select it if 't is on the same network and you know its IP address. Enter the IP address and click Choose Select Allow all applications (DMZplus mode) Click Save Confirm that the computer you selected is configured for DHCP If it is not, configure it for DHCP. See "Configuring DHCP" on page 20. Restart the computer. When the computer restarts, it receives a special P address from the gateway and all unassigned TCP and UDP ports are forwarded to it. To stop DMZplus mode on a particular computer, select it and then select Maximum protection. Chapter 3 Configuring the Gateway 23
How to change gateway settings?
Configuring the Gateway The gateway 's configured automatically by your service provider, but you can change certain settings, such as the wireless network name, password, and firewall options. Opening the gateway home page Use the gateway home page to change settings on your gateway. 1. Start your web browser 2. n the address bar, enter http://1 92.168.1.254 Refresh Page at&t U-verseu Home Services Settings Site Map Key Things to do Using Your Gateway Troubleshoot Wirel ess Restart your System Home Network Customize Firewall Gateway Status Conn83tion to AT&T Wirel ess Network ID Authentication type Network key Status VolP Line 1 Line 2 Home Network Devices 15 - Go to online support troubleshooting & AT&T eRepair - Mœiify or settings - Reboot the gateway - Find a computer, share a file - Adjust firewall settings for gaming and applications
How to connect to a Gateway?
Connecting devices to the gateway You can connect your computers and devices to the gateway using a wired or wireless connection. With either type of connection, you can use the first computer that you connect to the network to set up the gateway. Using a wired connection The gateway has four wired Ethernet ports that you can use to connect computers or other devices 1. Connect one end of the yellow Ethernet cable to one of the yellow Ethernet ports on the gateway 2. Connect the other end of the cable to the Ethernet port on the computer You can connect up to four computers to the gateway using the wired Ethernet ports Note: A 6-foot yellow Ethernet cable is provided with the gateway. If you need another cable, use a Cat 5 or Cat 5e Ethernet cable. After the gateway recognizes the computer, the Ethernet light turns steady green, and blinks when the computer starts transferring data with the gateway. Using a wireless connection The gateway has an integrated wireless access point that you can use to connect wireless devices to the gateway. By default, the gateway is configured with a network name (SSID) and WPA-PSK/WPA2-PSK security. 1. On the wireless device, view the available wireless networks. The specifics of how you do this depend on the device you are connecting. The SSID (default wireless network name) and wireless network key are printed on the label on the side of the gateway. Mac OS X users might have to enter the $1' character at the beginning of the encryption key. label 2. Select the appropriate wireless network name and connect. 3. At the prompt enter the wireless network key. After the gateway recognizes the wireless device, the Wireless light turns steady green, and blinks when the wireless device starts transferring data with the gateway. Chapter 2 Setting up the Gateway 11
How to connect a Gateway to the Internet?
10 Connecting the gateway to the Internet You can connect the gateway to the Internet using the DSL port or the Ethernet port. Using the VDSL port Connect the gateway to the Internet through the VDSL port. 1. Connect one end of a phone cord to the green VDSL port on the gateway. 2. Connect the other end of the phone cord to the phone outlet After the gateway recognizes the connection, the Broadband light blinks green for a moment and then turns steady green VDSL Using the Ethernet port If directed by your service provider, you can connect the gateway to the Internet through the Ethernet port. 1. Connect one end of an Ethernet cable to the Ethernet port on the gateway 2. Connect the other end of the Ethernet cable to the broadband device After the gateway recognizes the connection, the Broadband light blinks green for a moment and then turns steady green Chapter 2 Setting up the Gateway
Learn about port forwarding
Use port forwarding to route incoming and outgoing data on your home network from a remote location.
Add a new user-defined application
Sometimes, an application you want to access isn’t listed. Learn how to add a specific application.