Press MENU when the phone is not in use. Press or to scroll to Answering sys, then press SELECT. Press or to scroll to Ans sys setup, then press SELECT. Press or to scroll to Remote code, then press SELECT.
Full Answer
How do I contact VTech communications?
Regional Office - Telecommunication Products (VTech Branded Phones) VTech Communications, Inc. 9020 SW Washington Square Road, Suite 555 Tigard, OR 97223 United States . Tel: +1 503 596 1200. Fax: +1 503 644 9887. Customer Service Hotline: 1 800 595 9511 (6am - 6pm, Mon - Fri, Pacific Time)
How do I access ANS SYS remotely from a touch-tone phone?
system remotely from any touch-tone telephone. The preset code is 19. You can set the code from 00 to 99. Press MENU when the phone is not in use. Press or to scroll to Answering sys, then press SELECT. Press or to scroll to Ans sys setup, then press SELECT. Press or to scroll to Remote code, then press SELECT.
Does your VTech cordless phone have voicemail?
I bought a Vtech cordless phone. Everything works, but I bought a Vtech cordless phone. Everything works, but incoming calls go directly to voicemail. I have spoken to both the voicemail provider and the telephone service provider - the voice mail should kick in after 4 rings. I checked that the ringer volume is at the highest setting.
What is the model number of the VTech phone 2?
Vtech phone 2 handsets model CS6529-2. My voicemail is no Vtech phone 2 handsets model CS6529-2. My voicemail is no longer set up … read more
How do I reconnect my VTech phone to base?
1:042:17Set up and connect the telephone - VTech CS5249 - YouTubeYouTubeStart of suggested clipEnd of suggested clipYou will need the cordless handset its back cover and the battery pack install the battery to theMoreYou will need the cordless handset its back cover and the battery pack install the battery to the back of the cordless handset make sure you see this side up on the battery.
How do I turn off call forwarding on my VTech phone?
When you hear two beeps, Call Forwarding has been activated. To deactivate Call Forwarding, dial *73.
How do you reset a VTech cordless phone?
How to Reset a Vtech Cordless PhoneUnplug the power cable from the base of the Vtech.Reconnect the power cable to the base after a few minutes.Reinsert the battery into the handset.Put the handset in the handset cradle of the base. This will allow the devices to re-establish a link.
How do you troubleshoot a VTech cordless phone?
My phone is not working properly....Should this occur, we suggest this simple remedy:Unplug any power supplies connected to your product;Remove any installed batteries or battery packs;Wait 5 minutes;Plug the power supplies into the product;Install the batteries. ... Finally, try using your product as you normally would.
How do you deactivate call forwarding?
Contact UsOpen the Phone app.Tap the 3-dot menu button or the 3-line menu button.Look for “Call Forwarding” or “More settings”Tap 'Call forwarding'Select voice calls.Make sure all options are turned OFF.
What is * 73 on your phone?
Call forwardingCall forwarding is disabled by dialing *73. This feature requires a subscription from the telephone company. Also available in some areas is Remote Access to call forwarding, which permit the control over call forwarding from telephones other than the subscriber's telephone.
How do I reset my landline phone?
Try unplugging the phone and letting it sit for about 10 minutes. This should reset the phone. Try taking the battery out and then unplugging the base from the power and phone line.
Where is program button on VTech phone?
Step 1. Pick up the VTech cordless phone from the base. When the handset is not in use, press the "Prog" button, which will access the programmable directory. Using this directory, you can store up to 20 contacts and enter names that are up to 14 characters long, change the date and time and set your ringer.
Why does my cordless phone keep cutting out?
The most common culprit is a faulty line filter. All phones and fax machines in your premises must be plugged into a phone socket with a line filter. Plug your handset into the phone socket with a line filter and attempt to make a call.
Why has my landline suddenly stopped working?
If all the devices connected to your home landline don't have a dial tone, it may be because the copper wires connecting your home to the phone network have degraded. These wires may need to be replaced. Home phone copper line is a live wire, for safety reasons, it is not recommended to personally test the lines.
Why is my VTech phone not calling out?
A common issue users have when they do not hear a dial tone is that all the wires of the device are not actually plugged in. Fasten the phone cable into both the wall and the phone base. If the issue is still not resolved, then consider trying to connect a different, functional, telephone into the same cables.
What would cause phone not to have dial tone?
If you have no dial tone on your cordless phone, check the battery and charge it if it's low. Make sure your cordless phone's base unit is plugged into a working electrical outlet. Also make sure the phone cord is plugged securely into the wall phone jack.
Does VTech phones have call forwarding?
Call Forwarding Automatically forward incoming calls to an internal extension or external number. Tip: If you need to forward a single call, press the Forward softkey while your phone rings to send the caller to another person. Press the Menu softkey. Select Features > Call > Call forward.
How do you Unforward calls from a landline?
If you want to undo the call forwarding or change it to a different number, dial *73 from your phone line.
How do you forward calls on a VTech home phone?
1:532:35VTech VSP736 -- How do I set up call forwarding? - YouTubeYouTubeStart of suggested clipEnd of suggested clipIf you'd like to manually forward a call when your phone rings press the forward soft key you willMoreIf you'd like to manually forward a call when your phone rings press the forward soft key you will then need to type the extension or external. Number you would like to forward the call to that
How do I forward my home phone to my cell phone?
How to forward calls from a landline to your cell phoneLift the receiver of your landline phone and dial *72 after you hear the dial tone.Dial the 10-digit phone number you'd like to forward these calls to, followed by the # sign.Wait for confirmation that call forwarding has been successfully set up.
When the lights stabilize, should you be able to test the phone lines again?
When the lights "stabilize", then you should be able to TEST the phone lines againand see if calls can now be MADE going OUT, and received coming IN -WITHOUT the previous issue(s).
Is the battery in a Vtech phone good?
Vtech phone, battery is good, but can't call out and
How to set the date and time on a caller ID?
You can also set the date and time manually. PressMENU>> Press / to Set date/time >> PressSELECT. Enter month (MM), date (DD) and year (YY) >> Press SELECT. Enter hour (HH) and minute (MM) >> Press / for AM/PM
What does the RBRC seal on a battery mean?
The RBRC® seal on the nickel-metal hydride battery indicates that VTech Communications, Inc. is voluntarily participating in an industry program to collect and recycle these batteries at the end of their useful lives, when taken out of service within the United States and Canada.
Can you use a telephone base on a table?
The telephone base is ready for tabletop use. If you want to change to wall mounting, see page 9 for details.
Do you have to turn on the built in answering system?
The built-in answering system must be turned on to answer and record messages.
Is a cordless phone private?
For this reason, you should not think of cordless telephone conversations as being as private as those on corded telephones.
How to place base unit on desk?
To place your base unit on a desk or table, insert the desk/wall bracket as instructed below and shown in position one or two, depending on your preference of how you’d like the base unit to be angled .
How to change from pulse to touch tone?
If you have pulse (rotary) service, you can change from dial pulse to touch tone dialing during a call by pressing * TONE . This is useful if you need to send touch tone signals for access to telephone banking or long distance services .
What is position 2 on a phone?
This position is an alternate way to install your phone on a table or desk . Position two allows a different viewing angle to your handset and base unit . Refer to the position two diagrams above .
