How do I add a user to my DSC alarm?
0:162:08My Alarm Center - How to Change User Codes for a DSC Security PanelYouTubeStart of suggested clipEnd of suggested clipBefore you begin you will need the alarm systems master code in order to make any changes to add aMoreBefore you begin you will need the alarm systems master code in order to make any changes to add a user code press star five plus your master code enter the user number zero one to 32.
How do I open DSC control panel?
0:141:37Replacing Batteries in a DSC Power Series WT5500 Wireless KeypadYouTubeStart of suggested clipEnd of suggested clipTo do this simply firmly grasp the keypad on both sides. And lift the unit from the mounting plate.MoreTo do this simply firmly grasp the keypad on both sides. And lift the unit from the mounting plate. Your device will be mounted to the wall.
How do you clear the trouble light on a DSC alarm?
DSC alarms can go off for a number of reasons. To reset the alarm or the warning lights, enter your master code twice, press the reset button, and then enter “*72” if the alarm is still ringing.
How do I program my DSC alarm remote?
0:273:40A-1 Security Alarms, Inc. DSC How to use 4 Button Keyfob - YouTubeYouTubeStart of suggested clipEnd of suggested clipThree white and one red the buttons on the key fob have to be held down for two to three seconds toMoreThree white and one red the buttons on the key fob have to be held down for two to three seconds to trigger.
How do you arm and disarm a DSC alarm system?
2:307:20A-1 DSC How to Arm and Disarm your Power Series Alarm Panel - YouTubeYouTubeStart of suggested clipEnd of suggested clipFor 30 seconds to disarm your system type in your four-digit user code whenever the alarm is armedMoreFor 30 seconds to disarm your system type in your four-digit user code whenever the alarm is armed or an emergency feature is active.
How do I turn off my DSC alarm without the code?
Hold down the reset button for 2 seconds. Hold it down for at least 2 seconds to disengage the alarm.
How do I get rid of the yellow light on my DSC alarm?
Press the '7' key and you will receive a number corresponding to the affected zone. The indicated zone is reading a low battery condition and needs a replacement battery. Replace the battery in the contact and the condition will clear.
How do I get rid of the yellow trouble light on my DSC alarm?
The trouble light is an indication that something is not functioning properly on your DSC security system. When a trouble is present the system trouble indicator light will illuminate and the keypad will beep every 10 seconds. To silence the trouble beep simply press the # key on the keypad.
What does yellow triangle mean on DSC alarm?
system troubleIf your keypad is beeping or has the yellow triangle lit up this means that there is some kind of system trouble. This can be something as simple as a low battery, and usually is, or it could be something more serious such as a system tamper.
What is the installer code for DSC?
5555The default installer code for a DSC is 5555. The installer code is the code that is used to get into the DSC programming mode so you can set the system up and make changes to panel programming. Having the installer code is the most important part of setting up the system.
How do I reset my DSC keypad?
To reset the detectors, press and hold the Reset key for two seconds or press *72. If your code is not valid, the system will not disarm and a two-second error tone will sound. If this happens, try again. Enter the date.
How do I register my DSC keyfob?
Press and hold a button on the key fob. The system should recognize the key fob and display its serial number on the screen. Confirm the serial number is correct then press the [*] key. This will enroll the key fob.
Where is DSC control panel?
Your DSC Security System is made up of a DSC control panel, one or more keypads and various sensors and detectors. The control panel, which is a metal cabinet, will be mounted out of the way in a utility closet or in the basement. The metal cabinet contains the system electronics, fuses and back up battery.
How do I remove a DSC keypad?
0:151:11DSC Keypad Battery Change - YouTubeYouTubeStart of suggested clipEnd of suggested clipAnd put the keypad back on your base basically all you have to do is line up the tabs with theMoreAnd put the keypad back on your base basically all you have to do is line up the tabs with the inserts on the base. Give a little push. Down. And then you have changing your batteries and your keypad.
How do I reset my DSC keypad?
To reset the detectors, press and hold the Reset key for two seconds or press *72. If your code is not valid, the system will not disarm and a two-second error tone will sound. If this happens, try again. Enter the date.
How do I remove ADT DSC Impassa panel from wall?
0:101:45How to Replace Your ADT DSC Impassa Back-Up Battery - YouTubeYouTubeStart of suggested clipEnd of suggested clipThe small screwdriver just needs to fit down here on the bottom this little space and you just kindMoreThe small screwdriver just needs to fit down here on the bottom this little space and you just kind of pry out the keypad so it pops up a little bit then you can just lift this up above the keypad.
How to program a PK5500?
If you have a Full Message LCD Keypad (PK5500), use the < or > keys to scroll to the user you wish to program and press *
What to do if you don't know your FMC master code?
Enter your system’s master code (If you do not know your system’s master code, call FMC’s Service Department)
