The router should pick up on the plex server and registered the upnp setting for the ports it is broadcasting with to accomodate. If UPnP is on and its not working check your plex preferences remote access setup. In plex my is automatically using the ports translated in UPnP, no manual settings. and again those line up with the orbi uPNP page.
Full Answer
How to fix Plex Media Server not working on Netgear Nighthawk X10?
Disable the Plex Media Server on the Netgear Nighthawk X10 so it is not running. Disconnect the USB drive From the X10. Connect the USB drive to your computer. Transfer the files to the drive. After adding your files, connect the drive back to the X10 and start up Plex Media Server again.
Why is Plex remote access not working on my router?
NAT/UPnP Compatibility: Either NAT or UPnP (depending on your router model) need to be enabled in order for port forwarding to work properly. If these are not enabled or have different configurations set than required, Plex Remote Access will not work.
How do I use remote access on my Nighthawk router?
How do I use remote access on my Nighthawk router? 1. Launch an Internet browser on a computer that is not on your home network. 2. Type your router's WAN IP address into your browser's address or location field followed by a colon (:) and the custom port number.
How do I add media to my Netgear Nighthawk X10?
There are two ways to add media to the Nighthawk X10 (be sure to follow our media preparation info for the best results): If you have media on a USB drive, you can attach it directly to the Nighthawk X10 and then access the content on the drive. Disable the Plex Media Server on the Netgear Nighthawk X10 so it is not running
How to add files to a USB drive on a Netgear Nighthawk?
Add files directly to the USB drive from your computer. Disable the Plex Media Server on the Netgear Nighthawk X10 so it is not running. Disconnect the USB drive From the X10. Connect the USB drive to your computer. Transfer the files to the drive. After adding your files, connect the drive back to the X10 and start up Plex Media Server again.
What is the Netgear Nighthawk X10?
The Netgear Nighthawk X10 router is a quad core 1.7Ghz ARMv7 802.11ad WiFi-enabled unit, which has two USB3 ports for external storage. Embedded into the firmware is the option to install Plex Media Server and run it on this always-on device. The Plex Media Server performance is comparable to the existing Netgear RN2xx series of devices that Netgear offers and users should expect a similar experience with this unit.
How to setup Plex Media Server on the X10 router?
To get started with Plex Media Server on the X10 router, begin by plugging in a USB drive to one of the two USB3 ports. Once inserted, navigate to the router’s web interface and enter the Plex Media Server settings page.
Can the Nighthawk X10 transcode video?
Yes, but there are limitations. As mentioned before this device resembles the Netgear RN2xx series in specs and performance, thus this device as well as the RN2xx units can transcode video. The same restrictions that apply to the RN2xx series also apply here, so when transcoding video, it is not powerful enough to handle more than one transcoded stream (re-encoding the video content). When a video transcode is necessary, output will be limited to 480p maximum resolution.
How do I get the Plex Media Server Log Files from the device?
Plex Media Server logs can be downloaded from the server when using Plex Web App.
Where are files stored on the Nighthawk X10 unit?
For those who know their way around the Nighthawk devices and know how to get access to them here are a few key paths to find the Plex Media Server data directory and binaries .
How many MB/s does a thumb drive need for Plex?
For performance reasons, if you opt for using a thumb drive as the main USB device for Plex Media Server data, ensure you use a USB3 device capable of writing at least 45mb/s or you may encounter performance issues when streaming media.
Why is Plex not working?
There are many instances where several bugs are induced into the Plex application which causes it not to work as expected. Software all around us get updates every once in a while and sometimes these updates are not compatible with Plex. Hence its engineers roll out an update targeting this issue solely.
Why is Plex server error?
This usually occurs because Plex is a heavy application with numerous parameters going on simultaneously. If any one of these gets into an error state or load a bad configuration, it might be unusable.
Why does Plex Media Server buffer?
This scenario usually occurs when your internet connection is not sound which forces the server to use less bandwidth in order to provide access to the media.
What is plex media?
Plex is a client-server media stream and software suite. It has a Plex Media Server desktop application which is available on Windows, Ubuntu, and macOS. This applications allows you to organize different media files in your computer and allows players over the internet to access them if given the correct credentials.
What happens if you don't have a stable internet connection?
The same scenario also applies to the requesting computer; if you do not have a stable internet connection, you will not be able to request and stream media efficiently. First, you should check the number of devices running on your network (both the server and requesting computer).
How to run ncpa.cpl?
Press Windows + R, type “ ncpa.cpl ” in the dialogue box and press Enter.
Does a plex router need NAT?
If these are not enabled or have different configurations set than required, Plex Remote Access will not work.
Guide on catching those sneaky ads that manage to get past Pi-hole (Part 2, The chrome Inspector)
This is the second part of the series where I would post to show how to block those sneaky ads using Pi-hole. The first part is linked here.
Monitoring Pi-Hole - the next chapter is up
I've finally managed to write part 3 of my monitoring guide which will eventually include setting up the dashboard I posted here a few weeks ago.
Alanine - Browser add-on that can do stuff
As part of my university degree I've developed a simple web browser plugin (add-on) for remote control of Pi-hole. And where else to post about this, than here ?
Guide on catching those sneaky ads that manage to get past Pi-hole (Part 1 - Using the Pi-hole query log)
Since there are many posts on this sub talking ads that get past, I want to post a guide. Before this, I want to say how Pi-hole works.
Chicken and Egg problem with Asus Router WAN connection
I'm trying to figure out how to solve this particular problem. When I set my Asus router to use an internal IP address for DNS (pi-hole on RPi) under the WAN connection, it often doesn't connect to my ISP at all (Xfinity).
How to find the model number of a Netgear device?
To find the model/version number, check the bottom or back panel of your NETGEAR device.
How to remote access a router?
To use remote access: 1. Launch an Internet browser on a computer that is not on your home network. 2. Type your router's WAN IP address into your browser's address or location field followed by a colon (:) and the custom port number.
What is Gearhead support?
GearHead Support is a technical support service for NETGEAR devices and all other connected devices in your home. Advanced remote support tools are used to fix issues on any of your devices. The service includes support for the following:
