What is ReadyNAS remote and how does it work?
With ReadyNAS Remote, your ReadyNAS system and your remote devices access a remote server at NETGEAR and use a peer-to-peer (P2P) virtual private network (VPN) connection. Data transmission over the Internet goes through an encrypted tunnel, so your data stays private as it transfers to and from your ReadyNAS system.
How do I access the ReadyNAS admin page?
The ReadyNAS Admin Page can only be access when you are on the same network (LAN) as your device, unless you use the ReadyCLOUD Desktop client.. Not what you're looking for? Return to the ReadyCLOUD FAQ. After logging into ReadyCLOUD website remote from your network, you may notice some Admin Page links.
How do I enable SMB on my ReadyNAS network?
Log in to the management interface of your ReadyNAS account and go to the Sharestab. 2. Click on the share and click the Settingsbutton. 3. Go to the Network Accesstab. This action takes you to the SMB settings for the share. 4. Clear the read/write option for the Everyonegroup and enable access for users and groups as needed.
How do I enable readycloud on my ReadyNAS?
Log on to the ReadyNAS admin interface and go to the Cloudtab. 2. Verify that there is a green check mark beside the Internet Availableand Services Availablefields as shown below. If not, verify that the ReadyNAS has a valid default gateway and DNS configuration. 3. Turn ReadyCLOUD on by clicking the button marked in red below. 4.
How do I access my ReadyNAS remotely?
Using the computer from which you want to remotely access a ReadyNAS system, visit http://www.netgear.com/ReadyNAS-remote.
How do I access my ReadyNAS admin page?
Access the web admin page of the ReadyNAS by clicking Admin Page in RAIDar or enter the URL https://ReadyNAS_IP_address/admin - where ReadyNAS_IP_address is the IP Address seen in RAIDar.
How do I invite someone to ReadyCLOUD?
Visit the ReadyCLOUD portal at https://readycloud.netgear.com.Log in with your MyNETGEAR account.Hover your mouse over the share you want to invite a user to.Click the blue icon with the + sign.Decide how much access to grant to the user: ... Click Next.More items...
How do I access ReadyNAS duo?
You can use the RAIDar utility, or you can detect your ReadyNAS Duo by accessing your router and pasting the ReadyNAS Duo IP Address into your browser. Before using the RAIDar utility to detect your device, power on ReadyNAS and wait for it to boot up (approximately 2 minutes).
What is Netgear ReadyNAS default password?
The default credentials to log in to the local admin page are: Username: admin. Password: password.
How do I change my Netgear ReadyNAS IP address?
Click Change adapter settings. Right click on the connected NIC and click Properties. Select Internet Protocol Version 4 (TCP/IPv4) > click Properties. Select Use the following IP address > Enter an IP address in the range of 169.254.
How do I use ReadyCLOUD app?
Install ReadyCLOUD from the Google Play Store and launch it. Enter your MyNETGEAR username and password and click Sign On. The app connects and displays the ReadyNAS devices to which your MyNETGEAR account has access. Tap the ReadyNAS to which you want to connect.
How do I use ReadyCLOUD?
To use ReadyCLOUD, you must have a ReadyCLOUD account....Connect a USB storage device to your router's USB port.Go to ReadySHARE page, select ReadyCLOUD option, and enter your ReadyCLOUD user name and password.Your router is now registered with your ReadyCLOUD account.
How do I enable SSH on my Netgear ReadyNAS?
Enabling SSH access for root using a public/private key pair.Go to System > Settings > Services.Click on SSH.When prompted with the support warning, click Yes if you are sure you want to proceed.Select Enable SSH. ... Click Apply.Go to Accounts > Users.Click on the admin account and select Settings. ... Select SSH.More items...
How do I map a ReadyNAS to a network drive?
Mapping a network drive is a method to connect to a shared network folder, such as a share on a ReadyNAS storage system....To map a network drive in Windows 7 or Windows Vista:Click Start > Computer > Map network drive.In the window that opens, choose an available letter from the Drive list.More items...•
How do I reset my Netgear NAS?
Using a straightened paper clip, press and hold the Reset button. While continuing to hold the Reset button, press and release the Power button to power on the system. To perform an OS reinstall, continue to hold the Reset button until all Disk LEDs flash once, after about 5 seconds, and then release the button.
How do I access my Netgear NAS storage?
Visit http://readycloud.netgear.com on a computer that uses the same local area network (LAN) and Internet connection as your ReadyNAS system. Click the Start button under Set up a new ReadyNAS. Click the Discover button.
How do I reset my ReadyNAS?
Using a straightened paper clip, press and hold the Reset button. While continuing to hold the Reset button, press and release the Power button to power on the system. To perform an OS reinstall, continue to hold the Reset button until all Disk LEDs flash once, after about 5 seconds, and then release the button.
How do I reset my Netgear NAS password?
You can reset your ReadyNAS Admin password by accessing http://ip_address_of_readynas/password_recovery. If you have forgotten the password recovery answer, you will need to perform a firmware re-installation to reset the admin password.
How do I setup my Netgear NAS box?
1:203:04NETGEAR ReadyNAS Installation - YouTubeYouTubeStart of suggested clipEnd of suggested clipMake sure to choose a location that provides adequate ventilation connect the power adapter to yourMoreMake sure to choose a location that provides adequate ventilation connect the power adapter to your unit and the power cord into a wall outlet or power strip.
Can't find what you're looking for?
Quick and easy solutions are available for you in the NETGEAR community.
Complimentary Support
NETGEAR provides complimentary technical support for NETGEAR products for 90 days from the original date of purchase.
NETGEAR Premium Support
A single point of support around the clock. GearHead Technical Support makes it easy to fix issues on not just your NETGEAR purchase but for your entire home network. The service includes support for the following:
Complimentary Support
NETGEAR provides complimentary technical support for NETGEAR products for 90 days from the original date of purchase.
NETGEAR Premium Support
A single point of support around the clock. GearHead Technical Support makes it easy to fix issues on not just your NETGEAR purchase but for your entire home network. The service includes support for the following:
How to check ReadyNAS gateway?
1. Log on to the ReadyNAS admin interface and go to the Cloud tab. 2. Verify that there is a green check mark be side the Internet Available and Services Available fields as shown below. If not, verify that the ReadyNAS has a valid default gateway and DNS configuration.
How to give permissions to a document in ReadyCloUD?
As the ReadyCLOUD admin, you see all shares and have the rights to set permissions on these shares. 2. Right click on the Documents share and click the Permissions button. The permissions windows opens. 3.
What chapter is Remote Access to ReadyNAS?
Chapter 2 Remote Access to Your ReadyNAS
Where is the ReadyNAS remote icon?
The ReadyNAS Remote icon displays in the system tray.
How to register Netgear product?
After installing your device, locate the serial number on the label of your product and use it to register your product at https://my.netgear.com. You must register your product before you can use NETGEAR telephone support. NETGEAR recommends registering your product through the NETGEAR website. For product updates, additional documentation, and support, visit http://support.netgear.com. Phone (US & Canada only): 1-888-NETGEAR. Phone (Other Countries): Check the list of phone numbers at
When you create a ReadyNAS remote account, are you automatically logged in as that user?
When you create a ReadyNAS Remote account, you are automatically logged in as that user.
Can Cloud users access ReadyNAS?
Allow Cloud Users to Access Your ReadyNAS System on page 11). Cloud users can then access your ReadyNAS system remotely (see Chapter 2, Remote