Remote-access Guide

readynasnv+ says no shares accessible after setting up remote access

by Dr. Vince Lynch Published 2 years ago Updated 2 years ago

If you still do not see shares after logging into the ReadyNAS Remote application, stay logged in and go to FrontView and go to the Installed Add-ons page. On this page you can stop and start the ReadyNAS Remote addon by checking the box in the upper of the add-on and pressing Save; this will stop the add-on.

How do I access ReadyNAS shares?

To access a share using a network-attached Windows device:Ensure that the SMB file-sharing protocol is enabled on your ReadyNAS system. ... Enter in the Windows Explorer address bar. ... Enter a user ID and password. ... Windows Explorer displays the contents of all available shares on your ReadyNAS system.

How do I access my ReadyNAS admin page?

Access the web admin page of the ReadyNAS by clicking Admin Page in RAIDar or enter the URL https://ReadyNAS_IP_address/admin - where ReadyNAS_IP_address is the IP Address seen in RAIDar.

How do I enable SSH on my Netgear ReadyNAS?

Enabling SSH access for root using a public/private key pair.Go to System > Settings > Services.Click on SSH.When prompted with the support warning, click Yes if you are sure you want to proceed.Select Enable SSH. ... Click Apply.Go to Accounts > Users.Click on the admin account and select Settings. ... Select SSH.More items...

How do I reset my ReadyNAS?

Using a straightened paper clip, press and hold the Reset button. While continuing to hold the Reset button, press and release the Power button to power on the system. To perform an OS reinstall, continue to hold the Reset button until all Disk LEDs flash once, after about 5 seconds, and then release the button.

What is Netgear ReadyNAS default password?

The default credentials to log in to the local admin page are: Username: admin. Password: password.

How do I access ReadyNAS duo?

You can use the RAIDar utility, or you can detect your ReadyNAS Duo by accessing your router and pasting the ReadyNAS Duo IP Address into your browser. Before using the RAIDar utility to detect your device, power on ReadyNAS and wait for it to boot up (approximately 2 minutes).

How do I reset my ReadyNAS password?

You can reset your ReadyNAS Admin password by accessing http://ip_address_of_readynas/password_recovery. If you have forgotten the password recovery answer, you will need to perform a firmware re-installation to reset the admin password.

How do I reset my ReadyNAS 2100?

Power off your unit. Using a straightened paper clip, press and hold the SYS button. Press the Power button to power on the unit. Continue to press the SYS button until the LEDs are all lit....Your storage system has the following boot modes:Normal. ... Factory default.More items...

How do I reset my NAS password?

You can press the Reset button for 3 seconds to reset the administrator password to the default using a sharp object such as a paperclip or pin and insert it to the hole located below the "Reset" sign on the back of the unit. A little click can be felt when the button is pressed.

How do I access my Netgear NAS storage?

Visit http://readycloud.netgear.com on a computer that uses the same local area network (LAN) and Internet connection as your ReadyNAS system. Click the Start button under Set up a new ReadyNAS. Click the Discover button.

How do I change my Netgear ReadyNAS IP address?

Click Change adapter settings. Right click on the connected NIC and click Properties. Select Internet Protocol Version 4 (TCP/IPv4) > click Properties. Select Use the following IP address > Enter an IP address in the range of 169.254.

How do I use ReadyNAS remote?

0:032:03NETGEAR ReadyNAS Remote Access - YouTubeYouTubeStart of suggested clipEnd of suggested clipFrom any device the ready cloud web portal allows you to access your content from any browser simplyMoreFrom any device the ready cloud web portal allows you to access your content from any browser simply navigate to ready cloud Netgear comm and log in to your ready cloud. Account.

How do I reset my Netgear NAS password?

You can reset your ReadyNAS Admin password by accessing http://ip_address_of_readynas/password_recovery. If you have forgotten the password recovery answer, you will need to perform a firmware re-installation to reset the admin password.

A B C D E F G H I J K L M N O P Q R S T U V W X Y Z 1 2 3 4 5 6 7 8 9